Abstract:High entropy alloys (HEAs) have garnered significant attention in recent years, primarily focusing on alloying design and thermal processing. The objective of this study was to investigate the mechanical response of Al0.3CoCrFeNi, a representative HEA, under various stress states, temperatures, and strain rates, aiming to establish its constitutive equation and fracture criteria. Employing a hybrid FEM/EX approach, the constitutive behaviour of the alloy was characterized using the modified Johnson-Cook (MJC) model, while the fracture properties were assessed using the Hosford-Coulomb (HC) equation. Experimental findings highlighted the remarkable tensile strength (578.1 MPa) and ductility (69%) of the as-cast Al0.3CoCrFeNi at room temperature. However, at elevated temperatures ranging from 400 °C to 650 °C, a reduction in ductility was observed, accompanied by serration behaviour. Notably, precipitation hardening was detected at 800 °C, indicative of strengthening through precipitate formation. Additionally, Al0.3CoCrFeNi exhibited significant strain rate sensitivity and a positive strain rate effect, emphasizing its dynamic response under different loading conditions. The accuracy of the constitutive model and fracture criteria was validated through the examination of deformation and fracture modes in Taylor impact tests. The MJC model demonstrated predictions within a 10% deviation from experimental data, while the HC fracture criterion, accounting for stress triaxiality and Lode parameters, effectively predicted shear fracture in the projectiles. Crack formation in the projectiles resulted from a combination of tension and shear, followed by propagation at a 45° angle under combined compression and shear loading. This comprehensive study enhances understanding of the mechanical properties of Al0.3CoCrFeNi, providing valuable insights for its application in engineering, particularly in impact protection.

Investigation on High-Power Interior Combustion Engine Cylinder Friction Pair Material Selection by Hot Isostatic Pressing

AlCoCrFeNi HEA reinforced Al–Si–Mg alloy composite through hot-press sintering

Mechanical Properties and Tribological Behavior of Al0.5CoCrFeNb0.5Ni High-Entropy Alloy at High Temperatures

Microstructure and mechanical properties of Al-Fe-Co-Cr-Ni high entropy alloy fabricated via powder extrusion

The comparative research on tribological behavior of carbon-doped CoCrFeNiV high entropy alloys in air and vacuum environments

Investigation of mechanical behavior, constitutive modeling, and fracture criteria for as-cast Al0.3CoCrFeNi high entropy alloy

Effects of Ni/MoS2, Ag and Cr2O3 on the Microstructure and Mechanical Performance of a CoCrFeNi High-Entropy Alloy over a Wide Temperature Range

Hot isostatic pressing of ball milled novel grade high entropy alloys at different sintering time and the investigation of their mechanical and corrosion resistance properties

In Situ Development and High Temperature Features of CoCrFeNi-M6Cp High Entropy-Alloy Based Hardmetal

A New Type of High Entropy Alloy Composite Fe18Ni23Co25Cr21Mo8WNb3C2 Prepared by Mechanical Alloying and Hot Pressing Sintering

Tribological performance of a cost-effective CrFeNiAl0.3Ti0.3 high entropy alloy based self-lubricating composite in a wide temperature range

Investigation of phase transition, tribological behavior and wear mechanisms of WC-enhanced biphase eutectic high entropy alloy by fast hot pressing sintering

The Influence of Multi-Phase Intermetallic Compounds on the Microstructure and Tribological Behaviors of 6061 Al Alloy by Adding AlCoCrFeNi High-Entropy Alloy

Investigation of the Characteristics of Submicron-Structured Powder-Fabricated Cr50ni50 Alloys Via Different Hot-Press Sintering Pressures

Synthesis of high entropy alloy AlCoCrFeNiCuSn reinforced AlSi7Mg0.3 based composite developed by solid state technique

New High Strength and Heat Resistance Aluminum Alloy Material for Engine Cylinder Head

Effect of interstitial carbides on tribological properties of Co21Cr21Fe21Ni21V14.5C1.5 high entropy alloy at elevated temperature

Microstructure, Mechanical Properties, and Damping Capacity of AlxCoCrFeNi High-Entropy Alloys Prepared by Spark Plasma Sintering

High-entropy alloy coatings with excellent mechanical, corrosion resistance and magnetic properties prepared by mechanical alloying and hot pressing sintering

AlCoCrFeNi High Entropy Alloy Reinforced Cu-based Composite with High Strength and Ductility after Hot Extrusion

Microstructure and Tribological Properties of FeCoCrNi High-Entropy Alloy Coatings Fabricated by Atmospheric Plasma Spraying