Abstract:Aspheric thin-walled crucibles with large diameters are widely used for photovoltaics and semiconductor industries, while they have hard-brittle and aspheric characteristics. Nevertheless, these crucibles strictly require atomic surfaces and high material removal rate (MRR). This is a challenge for chemical mechanical polishing (CMP). To break this challenge, a novel green CMP was developed for fused silica, containing ceria, lanthana, hydrogen peroxide, diethylene triaminepentaacetic acid pentasodium, carboxymethyl cellulose sodium and guanidine carbonate. After CMP, surface roughness Ra of 0.115 is obtained at a scanning area of 5 × 5 μm2 measured by atomic force microscopy, and MRR is 563 nm/min. In such an atomic surface, the MRR is the highest compared with those published previously. Transmission electron microscopy confirms that the thickness of damaged layer after CMP is only 2.63 nm. A novel approach of robot floating polishing is proposed for aspheric crucibles with a diameter of 810 mm and a height of 580 mm. Using the developed CMP, surface roughness Sa of 0.178 nm on inner surface of an aspheric thin-walled crucible is achieved under a measurement area of 50 × 50 μm2. X-ray photoelectron spectroscopy (XPS) and electron paramagnetic resonance reveal that the content of Ce3+ increased from 28.54 to 43.76 %. Through Raman, XPS and Fourier transform infrared spectroscopy, CMP mechanisms are elucidated. Densified damaged layer on the surface of fused silica was induced by the transformation of surface structure from six-membered to four- or three-membered network. Ce-OH and Si-OH were formed between fused silica and ceria abrasives, forming Ce-O-Si by condensation reaction of dehydration. The developed green CMP and approach provide new pathway to polish and manufacture atomic surfaces for aspheric thin-walled crucibles with large diameters.

Comparative first-principles analysis of crystalline versus amorphous CeO2 particles: implications for chemical mechanical planarization

Elastic and Electronic Properties of Ce2O3 from First Principles

Mechanical and Electronic Properties of CeO 2 under Uniaxial Tensile Loading: A DFT Study

Influence of Cerium Oxide Abrasive Particle Morphologies on Polishing Performance

RE (la, Nd and Yb) Doped CeO2 Abrasive Particles for Chemical Mechanical Polishing of Dielectric Materials: Experimental and Computational Analysis

Mechanical wear behavior between CeO2(100), CeO2(110), CeO2(111), and silicon studied through atomic force microscopy

Oxidation differences on Si- versus C-terminated surfaces of SiC during planarization in the fabrication of high-power, high-frequency semiconductor device

Super fine cerium hydroxide abrasives for SiO2 film chemical mechanical planarization performing scratch free

Planar-dependent oxygen vacancy concentrations in photocatalytic CeO2 nanoparticles

Innovative synthesis of CeO 2 nanoparticles for advanced chemical mechanical polishing

Preparation of Surface Modified Ceria Nanoparticles As Abrasives for the Application of Chemical Mechanical Polishing (CMP)

Realization of atomic-level smooth surface of sapphire (0001) by chemical-mechanical planarization with nano colloidal silica abrasives

Atomic surface induced by novel green chemical mechanical polishing for aspheric thin-walled crucibles with large diameters

Trivalent lanthanum and ytterbium doped meso-silica/ceria abrasive systems toward chemical mechanical polishing (CMP) and ultraviolet irradiation-assisted photochemical mechanical polishing (PCMP)

The Effects of Ultra-Smooth Surface Atomic Step Morphology on CMP Performances of Sapphire and SiC Wafers

Investigation of Al/CeO2 interfacial relationships for epitaxial growth of Al on CeO2 substrates: first-principles calculation

Non-spherical abrasives with ordered mesoporous structures for chemical mechanical polishing

Study on uniform size and spherical CeO 2 abrasives synthesized by two-step method and their chemical mechanical polishing performances

First-Principles Calculated Structures and Carbon Binding Energies of Σ11 {101̅1}/ . -0pt{101̅1̅} Tilt Grain Boundaries in Corundum Structured Metal Oxides

Characterization of lanthanide elements doped ceria nanoparticles and its performance in chemical mechanical polishing as novel abrasive particles

Amorphization transition and electrical properties of La2− x Ce x CuO4 polycrystalline materials