Abstract:Cylindrical microlens arrays (CMLAs) play a key role in many optoelectronic devices, and 100% fill-factor CMLAs also have the advantage of improving the signal-to-noise ratio and avoiding stray-light effects. However, the existing preparation technologies are complicated and costly, which are not suitable for mass production. Herein, we propose a simple, efficient, and low-cost manufacturing method for CMLAs with a high fill-factor via the electric-field-driven (EFD) microscale 3D printing of polydimethylsiloxane (PDMS). By adjusting the printing parameters, the profile and the fill-factor of the CMLAs can be controlled to improve their optical performance. The optical performance test results show that the printed PDMS CMLAs have good image-projecting and light-diffraction properties. Using the two printing modes of this EFD microscale 3D-printing technology, a cylindrical dual-microlens array with a double-focusing function is simply prepared. At the same time, we print a series of specially shaped microlenses, proving the flexible manufacturing capabilities of this technology. The results show that the prepared CMLAs have good morphology and optical properties. The proposed method may provide a viable route for manufacturing large-area CMLAs with 100% fill-factor in a very simple, efficient, and low-cost manner.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsami.1c08652.EFD microscale 3D-printing principle and two printing modes; microfluidic chip structure and mixing effect verification; comparison of nanoimprint results of different hybrid methods of PDMS; effect of the nozzle size on the printing line width and height; effect of the printing height on the printing line width and height; schematic diagram of the imaging experiment of the PDMS CMLA; schematic diagram of the imaging experiment of the PDMS CMLA; and comparison of CMLAs manufactured by various technologies (PDF)High-speed photography of the micro-extrusion printing mode (MP4)Printing CMLAs with 100% fill-factor using the micro-extrusion mode (MP4)High-speed photography of the continuous cone jet printing mode (MP4)Printing CMLAs with 100% fill-factor using a continuous cone jet mode (MP4)Printing cylindrical dual-MLAs via two printing modes of EFD microscale 3D printing (MP4)Printing phoenix-shaped specially shaped microlenses by the continuous cone jet mode (MP4)Printing phoenix-shaped specially shaped microlenses by the microextrusion mode (MP4)This article has not yet been cited by other publications.

One-step fabricating a PDMS optical lens based on surface charging and edge pining effects of a PDMS droplet

In Situ Fabrication of a Tunable Microlens.

Fabrication of Miniaturized Variable-focus Lens Using Liquid Filling Technique

Solvent-tunable PDMS microlens fabricated by femtosecond laser direct writing

Observation Interface of PDMS Membrane in a Microfluidic Chip Based on One-Step Molding

A simple method for fabricating multi-layer PDMS structures for 3D microfluidic chips

Moldless Printing of Silicone Lenses With Embedded Nanostructured Optical Filters

Rapid fabrication of large-area concave microlens arrays on PDMS by a femtosecond laser

3D Printing of a PDMS Cylindrical Microlens Array with 100% Fill-Factor

Fabrication of Polymer Microlens Array with Controllable Focal Length by Modifying Surface Wettability

Fabrication of PDMS micro through-holes using micromolding in open capillaries

Rapid Fabrication of Semiellipsoid Microlenses Using 3D-Printing and Roll-to-roll Imprinting Process

Sol–gel concave micro-lens arrays fabricated by combining the replicated PDMS soft mold with UV-cured imprint process

Fabrication of Polymer Compound Microlens by Lens-on-lens Microstructures

Single-step Fabrication of Superhydrophobic Micro/nano Dual-Scale PDMS Film Replicated from Ultra-Low-surface-energy Mold

Fabricating SU-8 Photoresist Microstructures with Controlled Convexity–Concavity and Curvature through Thermally Manipulating Capillary Action in Poly(dimethylsiloxane) Microholes

Using Micromachined Molds, Partial-curing PDMS Bonding Technique, and Multiple Casting to Create Hybrid Microfluidic Chip for Microlens Array

Direct Fabrication of Microlens Arrays on PMMA with Laser-Induced Structural Modification

A Fast and Efficient Fabrication Method for Microlens Array by Using Picosecond Laser Induced Volume Swelling

Efficient Manufacturing of Microdome Array for Advanced Electronic and Optical Devices†

Dielectric Liquid Microlens Array with Tunable Focal Length Based on Microdroplet Array Created via Dip-Coating Method