Abstract:Here, we applied hot-rolling in conjunction with direct quenching and partitioning (HDQ&P) processes with different rolling schedules to a low-C low-Si Al-added steel. Ferrite was introduced into the steel by intercritical rolling and air cooling after hot-rolling. The effect of intercritcal deformation on the microstructure evolution and mechanical properties was investigated. The promotion of austenite stabilization and the optimization of the TRIP effect due to a moderate degree of intercritical deformation were systematically explored. The results show that the addition of 1.46wt% of Al can effectively promote ferrite formation. An intercritical deformation above 800°C can result in a pronounced bimodal grain size distribution of ferrite and some elongated ferrite grains containing sub-grains. The residual strain states of both austenite and ferrite and the occurrence of bainite transformation jointly increase the retained austenite fraction due to its mechanical stabilization and the enhanced carbon partitioning into austenite from its surrounding phases. An intercritical deformation below 800°C can profoundly increase the ferrite fraction and promote the recrystallization of deformed ferrite. The formation of this large fraction of ferrite enhances the carbon enrichment in the untransformed austenite and retards the bainite transformation during the partitioning process and finally enhances martensite transformation and decreases the retained austenite fraction. The efficient TRIP effect of retained austenite and the possible strain partitioning of bainite jointly improve the work hardening and formability of the steel and lead to the excellent mechanical properties with relatively high tensile strength (905MPa), low yield ratio (0.60) and high total elongation (25.2%).

Influence of Al addition on the grain boundary oxidation of Ultra High Strength Steels during hot coiling

Influence of Si Content on Selective Oxidation and Oxide Scale Phase Transition During Hot-Rolled Coiling

Improved Strength and Enhanced Pitting Corrosion Resistance of Al-Mn Alloy with Zr Addition

Effects of Cu Addition on the Microstructure and Properties of the Al–Mn–Fe–Si Alloy

Insight into scale transformation and internal oxidation mechanism of hot rolled Si Mn added high strength steel

Investigation of Effects of Aluminum Additions on Microstructural Evolution and Mechanical Properties of Ultra-High Strength and Vanadium Bearing Dual-Phase Steels

Investigation of Si, Mn, and C interactions during coiling of hot rolling model alloys

Effects of Al Addition on the Microstructure of Fe-Mn-Si Ultra-Fine Grain Steel Welded Heat Affected Zone

High-temperature oxidation behavior and subsurface phase transformation of high-Mn high-Al steel

Influence of Al Addition Strategy on the Microstructure of a Low‐Cr Oxide Dispersion‐Strengthened Ferritic Steel

Influence of Al content on the corrosion resistance of micro-alloyed hot rolled steel as a function of grain size

Microstructures, Tensile Properties and Corrosion Behaviors of Fe20Cr25NiNb Stainless Steels with Different Al Contents in Supercritical Carbon Dioxide

Effect of post-annealing on the oxidation behavior of hot rolled ODS-FeCrAl steel in liquid lead

Effects of Al addition on high temperature oxidation behavior of 16Cr ODS steel

Local Corrosion Behaviors in the Coarse-Grained Heat-Affected Zone in a Newly Developed Zr-Ti-Al-RE Deoxidized High-Strength Low-Alloy Steel

Effect of Aluminum Alloying on the Hot Deformation Behavior of Nano-bainite Bearing Steel

Effect of Cr on the Microstructure and Oxidation Properties of Co-Al-W Superalloys Studied by in Situ Environmental TEM

Effects of Ti and Cu Addition on Inclusion Modification and Corrosion Behavior in Simulated Coarse-Grained Heat-Affected Zone of Low-Alloy Steels

In-situ observation of grain refinement in the simulated heat-affected zone of high-strength low-alloy steel by Zr-Ti combined deoxidation

Effect of Intercritical Deformation on Microstructure and Mechanical Properties of A Low-Silicon Aluminum-Added Hot-Rolled Directly Quenched and Partitioned Steel

Influences of Al content on oxidation behavior of CoNiCrAlYRe alloys