Abstract:<span class="a-plus-plus abstract-section id-a-sec1 outputmedium-all"><p class="a-plus-plus">To improve comprehensive mechanical properties of Mg-Li alloy, alternative α/β Mg-Li composite sheets with a bimodal-grained structure were prepared by accumulative roll bonding (ARB). The microstructure, texture, mechanical properties and strain hardening behavior of the alternative α/β Mg-Li composite sheets were studied. The bimodal grain structure, with ultrafine grains (about 0.79 μm) in the α alloy and coarse grains (about 53.28 μm) in the β alloy, can be observed in the composite sheet. The dominant texture of α-Mg and β-Li alloys is {0002} basal texture and {110} texture, respectively. In the α alloy, the basal texture decreases gradually with the increase of ARB pass, and the non-basal texture is formed in the sheet processed by 5-pass ARB. The dislocation density of the composite sheet gradually increases and approaches saturation after 3-pass ARB process due to the balance between dislocation accumulation in the ARB process and dislocation annihilation in dynamic recovery. The sheet processed by 3-pass ARB has the preferable strength and plasticity, with yield strength, ultimate tensile strength, elongation of 204 MPa, 216 MPa, 22.73%, respectively. Compared with the as-annealed alloys before ARB, the strain hardening rate of the ARB composite sheets increases gradually at low stress (stage II). Mg-Li sheets produced by ARB process remain a high plasticity because of the longer softening stage (stage III), which is mainly contributed to the synergistic effect of the bimodal grain structure and the activation of non-basal texture.</p></span><span class="a-plus-plus abstract-section id-a-sec2 outputmedium-online"><h3 class="a-plus-plus">Graphic </h3></span>

Research on mechanical properties and electromagnetic shielding effectiveness in Mg-8Li-2Y-Zn/Al multilayered composites fabricated by asymmetric accumulative roll bonding

Microstructure, mechanical properties, and electrical conductivity of Mg–8Li–2Y–Zn/Al multilayered composites fabricated by cross asynchronous accumulative roll bonding

A Novel Processing for CNT-Reinforced Mg-Matrix Laminated Composites to Enhance the Electromagnetic Shielding Property

Microstructure, Texture, and Mechanical Properties of Alternate Α/β Mg–Li Composite Sheets Prepared by Accumulative Roll Bonding

The Evolution of Microstructure and Electromagnetic Interference Shielding Effectiveness of Mg-2Mn-1Ce Alloy Prepared by Accumulative Roll Bonding Process

Microstructure and Mechanical Properties of Ultra-Lightweight Mg-Li-Al/Al-Li Composite Produced by Accumulative Roll Bonding at Ambient Temperature

Microstructure evolution and mechanical behavior of α/β alternative Mg–Li alloy composite sheets with different initial thickness ratios prepared by accumulative roll bonding

X-band shielding properties of Mg-9Li matrix composite containing Ni0.4Zn0.4Co0.2Fe2O4 fabricated by multi-layer composite rolling

Simultaneous achievement of high electromagnetic shielding effectiveness (X-band) and strength in Mg-Li-Zn-Gd/MWCNTs composite

Preparation of Mg-6Zn-1La-0.5Zr alloy sheet with excellent mechanical properties and electromagnetic interference shielding effectiveness by extrusion plus rolling

Microstructure and Mechanical Properties of the Mg/Al Multilayer Fabricated by Accumulative Roll Bonding (ARB) at Ambient Temperature

Microstructure, Mechanical Properties and Strain Hardening Behavior of Alternative α/β Mg-Li Composite Sheets Prepared by Accumulative Roll Bonding

Synergistic Mechanism of Strengthening and Toughening of Tissue Regulation Response to Mg/Al Composite Laminates by Hard Plate Accumulative Roll Bonding

Response mechanism of matrix microstructure evolution and mechanical behavior to Mg/Al composite plate by hard-plate accumulative roll bonding

Roll bonding characteristics of the Mg/Zn/Cu/Al multilayered composite produced by the ARB process

Interface behavior and tensile properties of Mg-14Li-3Al-2Gd sheets prepared by four-layer accumulative roll bonding

Microstructure, Texture, and Mechanical Properties of Alternate <i>α</i> /<i>β</i> Mg-Li Composite Sheets Prepared by Accumulative Roll Bonding

Microstructure and Mechanical Properties of the Mg/Al Laminated Composite Fabricated by Accumulative Roll Bonding (Arb)

Microstructural evolutions and mechanical properties of multilayered 1060Al/Al–Al2O3 composites fabricated by cold spraying and accumulative roll bonding

Effect of Asymmetric Accumulative Roll-Bonding process on the Microstructure and Strength Evolution of the AA1050/AZ31/AA1050 Multilayered Composite Materials

Microstructure and mechanical properties of Al/Cu/Mg laminated composite sheets produced by the ARB proces