Abstract:The Mg-Gd-Y-Zn-Zr sheets with different accumulative rolling reduction were successfully prepared through the multi-passes hot rolling process. The accumulative rolling reduction significantly affects the mechanical properties of the resulting sheets through altering the fraction of dynamic recrystallization (DRX) grains and distribution of the broken interdendritic 14H-LPSO phase. In addition, the precipitated equilibrium β phase at grain boundaries can facilitate the DRX process through the particle-stimulated nucleation (PSN) mechanism. The sub-grain boundaries formed in the vicinity of the grain boundaries and within the coarse deformed grains, and then transformed into the high-angle grain boundaries (HAGBs) through incorporating the adjacent dislocation. The coarse deformed grains were also divided into several grains by the formation of HAGBs and the DRX grains at grain boundaries also spread into the coarse deformed grains, and thus the fraction of the DRX grains improved with the increase of the accumulative rolling reduction. The ambient temperature tensile strength anisotropy of the resulting sheets increases with further accumulative rolling reduction. The effectively broken interdendritic 14H-LPSO phases, which acts as the reinforcing short-fiber, significantly strengthen the tensile yield strength along the RD due to its decreased aspect ratio (d/l) and more dispersed distribution aligned along the RD. Thus, the tensile yield strength along the RD demonstrated the higher increment than that along the TD and 45° with increasing accumulative rolling reduction. The broken interdendritic 14H-LPSO phases aligned along the RD also contribute to the higher fracture elongation along the 45° due to its alignment parallel to the resolved maximum shear stress during tension. Furthermore, the larger accumulative strain is conducive to decreasing the tensile anisotropy of the resulting sheets at elevated temperature.

Interface behavior and tensile properties of Mg-14Li-3Al-2Gd sheets prepared by four-layer accumulative roll bonding

Microstructure, Texture, and Mechanical Properties of Alternate Α/β Mg–Li Composite Sheets Prepared by Accumulative Roll Bonding

Microstructure and Mechanical Properties of Ultra-Lightweight Mg-Li-Al/Al-Li Composite Produced by Accumulative Roll Bonding at Ambient Temperature

Microstructure, Texture, and Mechanical Properties of Alternate <i>α</i> /<i>β</i> Mg-Li Composite Sheets Prepared by Accumulative Roll Bonding

Microstructure, Mechanical Properties and Strain Hardening Behavior of Alternative α/β Mg-Li Composite Sheets Prepared by Accumulative Roll Bonding

Microstructure evolution and mechanical behavior of α/β alternative Mg–Li alloy composite sheets with different initial thickness ratios prepared by accumulative roll bonding

Microstructure and Mechanical Properties of the Mg/Al Multilayer Fabricated by Accumulative Roll Bonding (ARB) at Ambient Temperature

Microstructure and Mechanical Properties of the Mg/Al Laminated Composite Fabricated by Accumulative Roll Bonding (Arb)

Microstructure Evolution and Mechanical Properties of AZ31 Alloy with Accumulative Roll Bonding

Interfacial Bonding and Fracture Behaviors of AZ63 Magnesium Alloy Sheet Processed by Accumulative Roll Bonding

Microstructural evolution and mechanical properties of multilayered ARB6/3/6 2N Al processed by accumulative roll bonding

Microstructure, mechanical properties, and electrical conductivity of Mg–8Li–2Y–Zn/Al multilayered composites fabricated by cross asynchronous accumulative roll bonding

Revealing the evolution mechanisms of microstructure, texture and mechanical behavior in Zr702 alloy plates fabricated by accumulative roll bonding

Microstructure and Mechanical Properties of Al-Mg-Si Similar Alloy Laminates Produced by Accumulative Roll Bonding

Response mechanism of matrix microstructure evolution and mechanical behavior to Mg/Al composite plate by hard-plate accumulative roll bonding

Roll bonding characteristics of the Mg/Zn/Cu/Al multilayered composite produced by the ARB process

Microstructure and Mechanical Properties of the Accumulative Roll Bonded (arbed) Pure Magnesium Sheet

The Role of Interfaces on the Deformation Mechanisms in Bimodal Al Laminates Produced by Accumulative Roll Bonding

Microstructure and mechanical properties of ARB-processed AA1050/AA5052 multilayer laminate sheets during cryorolling

Effects of Accumulative Rolling Reduction on the Microstructure Characteristic and Mechanical Properties of Mg-Gd-Y-Zn-Zr Sheets Processed by Hot Rolling

Superplasticity and microstructure in Mg–Gd–Y–Zr rolled sheet