Abstract:The performance of the new generation aero-engine is strongly dependent on the application of integral blisk technologies, while the high-risk failure of integral disk joints severely restricts the promotion of those technologies. Therefore, the molecular dynamics method is used to investigate the influence of nanopores on the tensile properties of single crystal/polycrystalline Ni composites. The results show that the addition of single crystal nickel can increase the tensile strength of single crystal/polycrystalline Ni compared with polycrystalline nickel. The influence of pore position distribution on the tensile properties of single crystal/polycrystalline Ni is investigated. The simulation results show that nanopore defects in a single crystal region significantly aggravate the fracture at the single crystal/polycrystalline Ni interface. Pores not only penetrate the interface of composites but also rapidly expand inside the single crystal and the polycrystalline crystal, in which the interface of composites is further reduced resulting in the failure acceleration of single crystal/polycrystalline Ni composites. On the contrary, when the pores are in a polycrystalline region, the interface of single crystal/polycrystalline Ni hinders the amorphization of the polycrystalline nickel side and inhibits the pores from spreading toward the interface. When the pores are in the interface region, the pores do not continue to expand into the single crystal, but propagate inside the polycrystalline crystal. The effect of the porosity of interface pores on the tensile properties of single crystal/polycrystalline Ni is also discussed. It is found that the tensile strength of single crystal/polycrystalline Ni decreases rapidly when the void porosity exceeds 0.8%. Finally, the influence of the number of voids on the tensile properties while maintaining the porosity of the interface pores is analyzed. When the porosity of the prefabricated pores of the interface is kept constant at 0.8%, the larger the number of pores (i.e., the smaller the pores), the larger the elastic modulus. In the plastic deformation stage, due to the large number of dispersed small pore structures at the interface of the single crystal/polycrystalline Ni composites, the dislocation motion is hindered, which plays a certain strengthening role and improves the tensile strength of the single crystal/polycrystalline Ni composites. It can be concluded that single crystal/polycrystalline Ni with dispersed small pores has better tensile properties than those with large pores.

In-situ X-ray tomography investigation of pore damage effects during a tensile test of a Ni-based single crystal superalloy

An integrated microporosity model of 3D X-ray micro-tomography and directional solidification simulations for Ni-based single crystal superalloys

Quantitative Study of High-Frequency Fatigue Hole-Edge Stresses in Nickel-Based Single-Crystal Superalloy

In-Situ Study of High Temperature Tensile Fracture Mechanism of Mar-M247 Alloy

In-situ scanning electron microscopy studies of small fatigue crack growth in recrystallized layer of a directionally solidified superalloy

High-Cycle Fatigue Fracture Behavior and Stress Prediction of Ni-Based Single-Crystal Superalloy with Film Cooling Hole Drilled Using Femtosecond Laser

Study of Fatigue Crack Initiation and the Propagation Mechanism Induced by Pores in a Powder Metallurgy Nickel-Based FGH96 Superalloy

Fracture Behavior of a High Pressure Die Casting AlSi10MnMg Alloy with Varied Porosity Levels

Characterisation of damage evolution in plain weave SiC/SiC composites using in situ X-ray micro-computed tomography

Microstructural insights into fatigue short crack propagation resistance and rate fluctuation in a Ni-based superalloy manufactured by Laser powder bed fusion

In situ SEM-DIC technique and its application to characterize the high-temperature fatigue crack closure effect

Exploring the evolution and damage behaviors of multidimensional defects surrounding film holes in single-crystal nickel-based superalloys

In-situ SEM study on fatigue crack behavior of a nickel-based single crystal alloy at 950 °C and 1050 °C

Multi-stage dwell fatigue crack growth behaviors in a nickel-based superalloy at elevated temperature

Investigation of ductile damage in dual phase steel during tensile deformation by in situ X-ray computed tomography

Effect of Nanopores on Tensile Properties of Single Crystal/Polycrystalline Nickel Composites

Multi-Dimensional Revealing the Influence Mechanism of the δ Phase on the Tensile Fracture Behavior of a Nickel-Based Superalloy on the Mesoscopic Scale

Quantitative Analysis of 3D Pore Characteristics Effect on the Ductility of HPDC Al-10Si-0.3Mg Alloy through X-Ray Tomography

Effects of crack-γ/γ' interface relative distributions on the deformation and crack growth behaviors of a nickel-based superalloy

In-situ Observations of the Effects of Orientation and Carbide on Low Cycle Fatigue Crack Propagation in a Single Crystal Superalloy

Ultra high-temperature deformation in a single crystal superalloy: Meso-scale process simulation and micro-mechanisms