Abstract:Effect of recrystallization on DZ4 directionally-solidified nickel-base superalloy was investigated both at room temperature and high temperature of 673K. In-situ SEM surface observation were performed. Experimental results reveal that the material performance is strongly influenced by surface recrystallization layer. All specimens were prepared under conditions of shot peening and 4h 1220°C high temperature annealing. Different shot peening pressure specimens have different recrystallization states. High shot penning pressure specimens have clear and straight grain boundaries and the grain size appears to be a little bit larger. Recrystallization state seems not only affect the fatigue life, but also the crack initiation pattern and crack initiation life. Low shot peening pressure specimens have much lower fatigue life which is around 8-10% of virgin one, and SEM Real-time observation reveals that channeling cracks initiated at the early stage of fatigue life. High shot peening pressure specimens have higher fatigue life comparing to low shot peening pressure specimens, although it’s almost half lower than the virgin one, and cracks initiated not until middle or latter stage of fatigue life. Crack initiation life is also much longer than those of low shot peening pressure. Low shot peening pressure specimens seems not fully recrystallized, and its grain boundaries are much fragile which is responsible for high density microcracks initiation, and finally leads to the failure. Further nano-indention experiments on surface recrystallized layers show that higher shot peening recrystallized layers have much lower elastic module, which may explain the longer crack initiation life.

In-situ scanning electron microscopy studies of small fatigue crack growth in recrystallized layer of a directionally solidified superalloy

On the fatigue small crack behaviors of directionally solidified superalloy DZ4 by in situ SEM observations

On the Fatigue Short Crack Behaviors of Directionally Solidified Superalloy Dz4 by in Situ Sem Observations

Investigation of fatigue mesoscopic mechanical properties of a nickel-based superalloy by instrumented microindentation measurements

Fatigue Fracture Mechanism of a Nickel-Based Single Crystal Superalloy with Partially Recrystallized Grains at 550 C by In Situ SEM Studies

A Study of the Internal Deformation Fields and the Related Microstructure Evolution during Thermal Fatigue Tests of a Single-Crystal Ni-Base Superalloy

Effect of surface recrystallization on the low cycle fatigue behavior of directionally solidified superalloy DZ4 by in-situ SEM studies

Effect of Local Recrystallized Grains on the Low Cycle Fatigue Behavior of a Nickel-Based Single Crystal Superalloy

Effect of Recrystallization on Low-Cycle Fatigue Behavior of DZ4 Directionally-Solidified Superalloy

In-situ SEM study on fatigue crack behavior of a nickel-based single crystal alloy at 950 °C and 1050 °C

In Situ Scanning Electron Microscopy Analysis of Effect of Temperature on Small Fatigue Crack Growth Behavior of Nickel-Based Single-Crystal Superalloy

Influence of Strain Amplitude on Low-Cycle Fatigue Behaviors of a Fourth-Generation Ni-Based Single-Crystal Superalloy at 980 °C

In-situ fatigue behavior study of a nickel-based single-crystal superalloy with different orientations

In-situ Observations of the Effects of Orientation and Carbide on Low Cycle Fatigue Crack Propagation in a Single Crystal Superalloy

Influence of orientation and temperature on the fatigue crack growth of a nickel-based directionally solidified superalloy

Microstructural insights into fatigue short crack propagation resistance and rate fluctuation in a Ni-based superalloy manufactured by Laser powder bed fusion

Multi-stage dwell fatigue crack growth behaviors in a nickel-based superalloy at elevated temperature

The Analysis on the Low Cycle Fatigue Behavior of A Directionally Solidified Superalloy with Recrystallized Surface Layers

Crystallographic analysis on small fatigue crack propagation behaviour of a nickel‐based single crystal superalloy

In-situ SEM and EBSD Study on Fretting Fatigue Crack Initiation of a Directionally Solidified Ni-based Superalloy

In-situ SEM study of slip-controlled short-crack growth in single-crystal nickel superalloy