Abstract:In this study, Al-20 wt% Mg 2 Si composites were prepared using an in situ endogenous process method. Various amounts of Sc were added to the composites, and a heat treatment process was employed to optimize the microstructures of the materials and enhance the overall properties of the composites. The study results indicate that the addition of Sc has a significant positive effect on both the microstructure and mechanical properties of Al-20 wt% Mg 2 Si composites. The inclusion of Sc leads to a more regular and uniformly distributed morphology of the primary Mg 2 Si phase, accompanied by a significant reduction in grain size. Particularly, when the Sc content is 0.3 wt%, the composite exhibits the most notable grain refinement effect, resulting in the best mechanical performance. The tensile strength reaches 152.7 MPa, the hardness measures 92.9 HV and the elongation is 2.82%. Through the heat treatment process, the morphology and distribution of the initial Mg 2 Si phase in the composites were optimized, resulting in significant improvements in both the morphology and distribution of the initial Mg 2 Si phase and the eutectic structure. Consequently, the tensile strength increased to 204.3 MPa, the hardness reached 117.8 HV, and the elongation improved to 3.72%. Finite element simulation was employed to model the tensile behavior of real microstructures of Al-20 wt% Mg 2 Si-0.3 wt% Sc composite in both as-cast and heat-treated conditions. The simulation results demonstrate good agreement with experiment. The fracture modes observed in both cases involve interfacial debonding and intergranular fracture. The simulation effectively showed the deformation process and stress distribution during tensile fracture. Moreover, the heat-treated model exhibits a higher load on the particles compared to the as-cast state. This finding provides evidence that the overall properties of Al-Mg 2 Si composites are enhanced following the heat treatment process.

Effect of Sc on damping properties, compressive and tensile strength of Fe-Cr-Al alloy

Effects of Sc on the Vacancy and Solute Behaviours in Aluminium

EFFECT OF Sc ON MICROSTRUCTURE AND PROPERTIES OF Al-Li-Cu-Mg-Zr ALLOY

Effects of Sc addition on microstructure, phase evolution and mechanical properties of Al0.2CoCrFeNi high-entropy alloys

Effect of Sc contents on the mechanical properties and damping capacity of Al-Zn-Mg-Cu-Zr-Sc alloys with different grain structures

Effect of Minor Sc Addition on the Microstructure Evolution of Al–Cu–Li–Mg Alloy During Homogenization with Different Cooling Modes

Effect of Sc on Al3Fe phase and mechanical properties of as-cast AA5052 aluminum alloy

Effect of minor Sc additions on precipitation and mechanical properties of a new Al-Cu-Li alloy under T8 temper

Effect of Sc content on microstructure characteristics and evolution of W phase in Al–Cu–Li alloys under as-cast and homogenization conditions

Effect of rare-earth Sc on the interface microstructure and mechanical properties of Al/steel bimetallic composites prepared by liquid–solid casting

Effect of Scandium on Grain refinement mechanism and Mechanical Properties of Al-7Si-0.6Mg alloy at Different Cooling Rates

Influence of the interaction between Si and Sc on the microstructure and tensile properties of as casted Al-Si-Sc alloys

Effect of Sc Addition and Heat Treatment on the Fracture Behavior of Al-20%Mg2Si Composites: Experiments and Finite Element Simulations

Enhanced strength of a high-conductivity Cu-Cr alloy by Sc addition

Nano-phase transformation of composite precipitates in multicomponent Al-Mg-Si(-Sc) alloys

Microstructures evolution and mechanical properties disparity in 2070 Al-Li alloy with minor Sc addition

Tailoring thermal conductivity and microstructure of Al–Fe alloys by addition of Sc 2 O 3 and variable cooling rates

Effects of scandium addition on microstructure, mechanical and thermal properties of cast Be-Al alloy

Effect of scandium on microstructure and mechanical properties of high zinc concentration aluminum alloys

Effect of Sc on the microstructure and mechanical properties of direct laser-deposited/Al-Cu-Mg-Sc composite coatings

Enhancing the strength of Sc-containing Al-Cu-Li alloys by modifying the precipitation behavior through plastic deformation and heat treatment