Abstract:In this study, Al-20 wt% Mg 2 Si composites were prepared using an in situ endogenous process method. Various amounts of Sc were added to the composites, and a heat treatment process was employed to optimize the microstructures of the materials and enhance the overall properties of the composites. The study results indicate that the addition of Sc has a significant positive effect on both the microstructure and mechanical properties of Al-20 wt% Mg 2 Si composites. The inclusion of Sc leads to a more regular and uniformly distributed morphology of the primary Mg 2 Si phase, accompanied by a significant reduction in grain size. Particularly, when the Sc content is 0.3 wt%, the composite exhibits the most notable grain refinement effect, resulting in the best mechanical performance. The tensile strength reaches 152.7 MPa, the hardness measures 92.9 HV and the elongation is 2.82%. Through the heat treatment process, the morphology and distribution of the initial Mg 2 Si phase in the composites were optimized, resulting in significant improvements in both the morphology and distribution of the initial Mg 2 Si phase and the eutectic structure. Consequently, the tensile strength increased to 204.3 MPa, the hardness reached 117.8 HV, and the elongation improved to 3.72%. Finite element simulation was employed to model the tensile behavior of real microstructures of Al-20 wt% Mg 2 Si-0.3 wt% Sc composite in both as-cast and heat-treated conditions. The simulation results demonstrate good agreement with experiment. The fracture modes observed in both cases involve interfacial debonding and intergranular fracture. The simulation effectively showed the deformation process and stress distribution during tensile fracture. Moreover, the heat-treated model exhibits a higher load on the particles compared to the as-cast state. This finding provides evidence that the overall properties of Al-Mg 2 Si composites are enhanced following the heat treatment process.

Effect of Sc on the microstructure and mechanical properties of direct laser-deposited/Al-Cu-Mg-Sc composite coatings

The effects of trace Sc addition on mechanical property and wear behavior of 2024/TiC composite coating processed by laser melting deposition

EFFECT OF Sc ON MICROSTRUCTURE AND PROPERTIES OF Al-Li-Cu-Mg-Zr ALLOY

Microstructure and Properties of TiC/AlMgSc Composites by Selective Laser Melting

Effect of rare-earth Sc on the interface microstructure and mechanical properties of Al/steel bimetallic composites prepared by liquid–solid casting

Effect of Sc microalloying on fabrication, microstructure and mechanical properties of SiCp/Al–Cu–Mg-Sc composites via powder metallurgy

Effects of Sc Addition on the Microstructure and Mechanical Properties of Cast Al-3Li-1.5Cu-0.15Zr Alloy

Microstructure and Tribological Behavior of Laser Cladding TiAlSi Composite Coatings Reinforced by Alumina–titania Ceramics on Ti–6Al–4V Alloys

Effect of Sc Addition and Heat Treatment on the Fracture Behavior of Al-20%Mg2Si Composites: Experiments and Finite Element Simulations

Effect of Sc microalloying on microstructure evolution and mechanical properties of extruded Al-Zn-Mg-Cu alloys

Microstructure and Mechanical Properties of Al–Si–Mg–Cu–Ti Alloy with Trace Amounts of Scandium

Addition of Sc in Wire-Based Directed Energy Deposition of Al–Mg–Zn–Cu Alloy: Microalloying to Refine Grains and Improve Mechanical Properties

Influence of Sc Content on the Microstructure and Mechanical Properties of Cast Al-2Li-2Cu-0.5Mg-0.2Zr Alloy

The Effects of the Addition of Ti3SiC2 on the Microstructure and Properties of Laser Cladding Composite Coatings

Effect of WC Addition on Microstructure and Tribological Properties of Bimodal Aluminum Composite Coatings Fabricated by Laser Surface Alloying

Microstructures and Properties of Laser Cladding Al-TiC-CeO₂ Composite Coatings

Microstructure and Mechanical Properties of a Novel Al-Mg-Sc-Ti Alloy Fabricated by Laser Powder Bed Fusion

Influence of Sc on microstructure and mechanical properties of Al–Si–Mg–Cu–Zr alloy

Microstructures and Properties Evolution of Spray-Deposited Al-Zn-Mg-Cu-Zr Alloys with Scandium Addition

Laser metal deposition for additive manufacturing of AA5024 and nanoparticulate TiC modified AA5024 alloy composites prepared with balling milling process

Effect of Sc on damping properties, compressive and tensile strength of Fe-Cr-Al alloy