Abstract:Abstract This paper presents an overview of a systems approach to the design and troubleshooting of IRCVs (Injection Rate Control Valves) used in deepwater chemical injection systems. The inherent problems associated with these simple flow regulators stem largely from the failure of design engineers to take a systems view in design. Along with the application of lessons learned from previous IRCV system failures, this systems approach provides a design method which will allow users to avoid many of the pitfalls inherent in design, installation, testing, commissioning and operation of IRCV systems. Introduction The conventional approach to injection of specialty/commodity chemicals is to use a separate chemical injection pump for each injection point. For topsides injection at low to moderate pressures, these pump systems are small and relatively inexpensive. In certain applications, such as in deepwater where injection pressures are high, these pump systems can be large, heavy and expensive. In deepwater and high pressure applications, a common alternative is to use distributed delivery systems featuring Injection Rate Control Valves (IRCVs). IRCVs are simple flow regulators which are designed to control flow to the individual users. It is easy to appreciate why these devices are being used with increasing frequency. Systems featuring them are cheaper, lighter, smaller and more flexible. However, many operators have little confidence in them. Many IRCV installations have failed and some have been made to work only after significant effort. While it can be difficult to definitively determine the particular reasons for their failure in many cases, it is not hard to picture why so many systems fail; there are multiple number of things that can go wrong with these systems. Failure to take a systems view explains many of the IRCV system failures. This paper presents a systems approach to the design and troubleshooting of IRCV systems. Our model of IRCV systems consists of two governing equations; 1) the injection system flow equation (pressure drop) and 2) the force balance across the IRCV piston. The force balance across the piston is important because the position of the piston determines the pressure drop and flowrate through the IRCV. Solving the system pressure drop equation simultaneously with the IRCV piston force balance is analogous to determining the operating point of a pump as the intersection of the pump curve and the system curve. Solving the system equations simultaneously is important because the design of the injection system impacts the operation of the IRCV. For example, system pressure drop impacts IRCV turndown and proportional offset. This paper includes:Descriptions of IRCVsDevelopment of the system modelA list of lessons learned, andA proposed design methodology.

Supervision and Control System of the Operational Variables of a Cluster in a High-Pressure Gas Injection Plant

System Requirements and Design Challenges of the Gas Injection System of Iter

ADVANCED AUTOMATIC SYSTEM FOR REMOTE CONTROL IN THE OIL AND GAS INDUSTRY

Surface Facilities Development for Steam Flue Gas Injection in a Colombian Heavy Oil Reservoir

Active Control System to Prevent Malfunctioning Caused by the Pressure Difference in Gasket Plate Heat Exchangers Applied in the Oil and Gas Industry

The Design of Low Cost Valve-and-pump Compounded Pressure Control System for the Hydro Viscous Clutch

Well Production Optimization through Annulus Gas Management using Gas Handling System in Auca Field, Ecuador.

Experimental Research of Simultaneous Water and Gas Injection Technology into Injection Wells using Mixing Devices

Modelling and predictive control of a new injection system for compressed natural gas engines

Evaluation of Pressure Maintenance by Internal Gas Injection in Volumetrically Controlled Reservoirs

Study and Realization of Automatic Control for Variable Flow Heating Systems

Design of Surface Facilities for a High-Pressure Miscible Gas Injection Pilot Scheme

Successful Application of Chemical Injection Rate Control Valves

Development of computer–integrated systems for the automation of technological process of associated gas processing

A Investigation of Fuzzy Control for Gas-injection Pressure in Gas-Assisted Injection Molding

Auto Control System Design of the Heat-exchanging Station with Rockwell Micro2080 and MCGS

Plantwide Control: A New Design Procedure and Its Application at Liquefied Petroleum Gas Facility (LPGF) Plant

Control and operation of the gas injection systems for KSTAR tokamak

Intelligent control of gas-assisted injection molding control systems

Optimization of the gas-assisted injection moulding process using multiple gas-injection systems

Design of a supervisory control system for autonomous operation of advanced reactors