Abstract:Abstract Steam quality surveillance is important for steam injection since the oil production response expected depends on the heat injected to the reservoir. This paper focuses on the evaluation of a mechanical device whose target is to increase the steam quality by means of physical principles such as centrifugal force and gravity, removing the water liquid phase not converted into steam as a result of the design limitations that a steam generator has in terms of steam dryness by scale deposition in the boiler piping. The following program was implemented to test the device, a cyclonic condensate separator, including different operational ways for disposing of the liquid phase removed by the separator. To begin, the separator was engaged to a steam generator outlet (25 MMBTU/hr capacity). A group of 3 wells close to the steam generator was selected to compare three operative ways for handling the hard and hot water removed by the cyclonic separator. An additional liquid phase sampling trap was installed downstream of the separator in the steam line to verify the steam quality by means of digital conductivity measurements. Steam injection on selected wells started sequentially and operational parameters as pressure, temperature, conductivity, steam quality, and gallons per minute (GPM) were collected from the steam generator and the cyclonic separator. Theoretical calculations for determining the heat generated, removed (via the liquid phase) and finally injected into the wells in MMBTU were done by using variables such as feeding water, operation time, enthalpy and steam quality, contrasting results obtained against the values given by the cyclonic separator. Finally, production results are shown and analyzed although they are not considered as relevant for evaluating the cyclonic separator effectiveness, since the main objective of the pilot was to check the steam quality increasing (above 95%) at field conditions. By using the cyclonic condensate separator, the injected steam quality increased from 81% to 98% on average during 41 operation days in a row. This improvement also was confirmed by the steam-trap installed downstream of the cyclonic separator (only 1.6% difference). The steam pressure and temperature losses caused by the cyclonic separator were 17% and 5% on average, respectively. From the cyclonic separator data and theoretical calculations, it was determined the cyclonic steam separator removed 227 bbl of water per day (17%) on average from the initial volumetric flow rate given by the generator (1407 water bbl/day at 41 GPM). In terms of energy, the cyclonic separator removed as liquid condensate 8% (41 MMBTU/day) of the initial energy given by the generator (527 MMBTU/day), in search of increasing the steam quality. From the three disposal options considered for the liquid phase that was removed, it was determined that injecting the liquid directly into the main production line was the most efficient way for handling this fluid, since it was observed that the hot water (354 °F and 21% flash steam) acted as a hot spot, improving the oil mobility inside the pipeline. This approach also reduces the costs of transporting the water removed to the treatment facility.

Surface Facilities Development for Steam Flue Gas Injection in a Colombian Heavy Oil Reservoir

Optimization of Steamflooding Heavy Oil Reservoirs

Combining Steam and Flue Gas as a Strategy to Support Energy Efficiency: A Comprehensive Review of the Associated Mechanisms

Study on Flow Characteristics of Flue Gas and Steam Co-Injection for Heavy Oil Recovery

Improving the Steam Quality injected in a Heavy Oil Reservoir by Using a Cyclonic-Type Condensate Separator: A Field Pilot

Technical Evaluation of a Surfactant Injection Process for Heavy Oil Recovery by Laboratory-Scale Numerical Simulation

Naphtha co-injection with steam effects on Colombian heavy crude oils quality by FTIR and 1 H NMR spectroscopy

Thermal flue gas utilization in delivering unconventional geo-energy

Heavy Oil Extraction in Texas with a Novel Downhole Steam Generation Method: A Field-Scale Experiment

Study on Thermal Chamber Expansion of VH-SAGD Process Using CO2-Inducing Effect for Heavy Oil Reservoirs

Improving Thermal Efficiency and Reducing Emissions with CO2 Injection during Late Stage SAGD Development

A Novel Workflow of Greenhouse Gas Capture and Utilization in Well Health Issue

Investigation of flue gas water-alternating gas (flue gas–WAG) injection for enhanced oil recovery and multicomponent flue gas storage in the post-waterflooding reservoir

Application of Flue Gas Foam-Assisted Steam Flooding in Complex and Difficult-to-Produce Heavy Oil Reservoirs

Study on the Variation of Crude Oil and Flue Gas Components in Flue-Gas-Assisted Steam Flooding

A Comprehensive Feasibility Study of a Production Technique to Lift Extra-Heavy, High-Viscosity Oil with an ESP System Demonstrates Improvement of Flow Assurance and Oil Production

Experimental Investigation and Numerical Simulation of Dynamic Characteristics for Multithermal Fluid-Assisted SAGD in Extraheavy Oil Reservoir

Development and Evaluation of a New Electrical Submersible Pump for High Viscosity Environments

Simple Optimized Module for Flared Gases Recovery

Integrated simulation system of CO2 gas injection application for enhanced oil recovery in the oil field

Experimental and numerical investigation on extra-heavy oil recovery by steam injection using vertical injector -horizontal producer