Abstract:Solid-state lithium (Li) metal batteries are widely used due to their excellent safety, superior energy density, and low cost. Nevertheless, the practical application of solid-state Li batteries is hindered by the inferior ionic conductivity of the solid electrolyte and poor interface contact between the electrode and electrolyte. Herein, a flexible, hybrid ceramic-based electrolyte was fabricated by a solution-casting method using poly(vinylidene fluoride), Li1.4Al0.4Ti1.6(PO4)3 powders, and lithium bis(trifluoromethanesulfonyl)imide. To realize high ionic conductivity and a stable self-viscous electrode/electrolyte interfacial contact simultaneously, a mixed solution of 1-ethyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide, lithium bis(trifluoromethanesulfonyl)imide, and fluoroethylene carbonate was introduced by the solution-infiltration method. The self-viscous Li1.4Al0.4Ti1.6(PO4)3 ceramic-based electrolyte exhibits superior ionic conductivity (2.4 × 10–4 S cm–1 at 25 °C), a high ionic transference number (0.42), wide voltage window (4.8 V vs Li/Li+), excellent thermal stabilities, and the ability to impede Li dendrite growth. In particular, the stable contact, low interfacial resistance, and fast ion-transport channels between the electrodes and solid electrolytes can be achieved by the self-viscous interfacial layer. The solid-state LiFePO4|Li battery assembled with the solid self-viscous electrolyte demonstrates a satisfactory initial discharge capacity of 138.0 mAh g–1 and capacity retention of 96.5% after 200 cycles at 0.5 C and under 25 °C. The self-viscous modification strategy of the solid electrolyte affords promising options for implementing the intimate electrode/electrolyte interfacial contact in high-energy-density solid-state batteries.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acs.energyfuels.1c01202.Figure S1: XRD patterns and SEM image of LATP ceramic powders. Figure S2: Temperature dependence of ionic conductivities for LATP pellets. Figure S3: Flexible and winding performances of self-viscous PLL-LEF electrolyte. Figure S4: Surface morphology of PL and PLL-LEF electrolytes. Figure S5: Adhesiveness exhibitions of PLL-LE composite electrolyte. Figure S6: EIS profiles of 10LiTFSI-40EMITFSI and 10LiTFSI-40EMITFSI-10FEC electrolytes. Figure S7: EIS profiles of stainless steel|PLL-LEF|Li cells. Figure S8: Thermogravimetry curve of PLL-LEF electrolyte. Figure S9: Flammability test of routine Celgard separator. Figure S10: EIS profiles of Li|PLL|Li cell for different aging times. Figure S11: Optical photographs of the PLL electrolyte. Figure S12: Ti 2p XPS of the PLL electrolyte. Figure S13: EIS profiles of Li symmetric cell with different electrolytes after cycling. Figure S14: Constant current cycling curves of Li|PLL-LEF|Li cells at 0.2 mA·cm–2. Figure S15: Constant current cycling curves of Li|PLL-LEF|Li cells at 0.5 mA·cm–2. Figure S16: Constant current cycling curves of Li|PLL-LEF|Li cells. Figure S17: High multiple SEM images of Li surfaces obtained from Li symmetrical cells. Figure S18: SEM image of pristine Li surface. Figure S19: EIS results of LiFePO4|PLL|Li, LiFePO4|PLL-LE|Li and LiFePO4|PLL-LEF|Li batteries. Figure S20: Typical charge–discharge voltage profiles of LiFePO4|PLL-LE|Li cell at 0.5 C. Figure S21: Electrochemical properties of Al2O3@LiNi0.5Co0.3Mn0.3O2|PLL-LEF|Li cell (PDF)This article has not yet been cited by other publications.

Strong Interfacial Adhesion between the Li 2 S Cathode and a Functional Li 7 P 2.9 Ce 0.2 S 10.9 Cl 0.3 Solid-State Electrolyte Endowed Long-Term Cycle Stability to All-Solid-State Lithium–Sulfur Batteries

A Dynamically Stable Sulfide Electrolyte Architecture for High-Performance All-Solid-State Lithium Metal Batteries

Silicon-Doped Argyrodite Solid Electrolyte Li 6 PS 5 I with Improved Ionic Conductivity and Interfacial Compatibility for High-Performance All-Solid-State Lithium Batteries

Enhanced air-stability and high Li-ion conductivity of Li6.988P2.994Nb0.2S10.934O0.6 glass-ceramic electrolyte for All-Solid-state Lithium-Sulfur Batteries.

Cathode-Supported-Electrolyte Configuration for High-Performance All-Solid-State Lithium–Sulfur Batteries

Synergistic Li6PS5Cl@Li3OCl Composite Electrolyte for High-Performance All-Solid-State Lithium Batteries

Tailored Li2s-P2s5 Glass-Ceramic Electrolyte By Mos2 Doping, Possessing High Ionic Conductivity For All-Solid-State Lithium-Sulfur Batteries

Design Unique Air‐Stable and Li–Metal Compatible Sulfide Electrolyte via Exploration of Anion Functional Units for All‐Solid‐State Lithium–Metal Batteries

An All-Solid-State Battery Based on Sulfide and PEO Composite Electrolyte.

Integrated Structure of Cathode and Double-Layer Electrolyte for Highly Stable and Dendrite-Free All-Solid-State Li-Metal Batteries

Stabilizing Ceramic-Based Electrolyte Interfaces with Self-Viscous Modification Strategy for Solid-State Lithium Batteries

Improved Ionic Conductivity and Li Dendrite Suppression Capability toward Li 7 P 3 S 11 -Based Solid Electrolytes Triggered by Nb and O Cosubstitution

Tailored Li 7 P 3 S 11 Electrolyte by In 2 S 3 Doping Suppresses Electrochemical Decomposition for High-Performance All-Solid-State Lithium–Sulfur Batteries

Amorphous Titanium Polysulfide Composites with Electronic/Ionic Conduction Networks for All-Solid-State Lithium Batteries

Achieving high-performance Li6.5Sb0.5Ge0.5S5I-based all-solid-state lithium batteries

All-solid-state batteries with Li2O-Li2S-P2S5 glass electrolytes synthesized by two-step mechanical milling

A highly stable and conductive cerium‐doped Li7P3S11 glass‐ceramic electrolyte for solid‐state lithium–sulfur batteries

Rationally Designed in-Situ Gelled Polymer-Ceramic Hybrid Electrolyte Enables Superior Performance and Stability in Quasi-Solid-State Lithium-Sulfur Batteries

High Capacity, Superior Cyclic Performances in All-Solid-State Lithium-Ion Batteries Based on 78Li2s-22P2s5 Glass-Ceramic Electrolytes Prepared Via Simple Heat Treatment

Engineering high conductive Li7P2S8I via Cl- doping for all-solid-state Li-S batteries workable at different operating temperatures

Integrating Lithium Sulfide as a Single Ionic Conductor Interphase for Stable All-Solid-State Lithium-Sulfur Batteries