Abstract:Statement of problem: Heat treatment has been used to reduce the residual stress of alloys fabricated by selective laser melting (SLM) to avoid deformation. Co-Cr metal-ceramic alloys are used to fabricate metal-ceramic restorations and removable partial dentures (RPDs) on the same substrate by SLM. A heat treatment that enables the fabrication of metal-ceramic restorations and RPDs with excellent mechanical properties should be evaluated. Purpose: The purpose of this in vitro study was to determine the effects of 2 heat treatments on the mechanical properties of SLM Co-Cr metal-ceramic alloys intended for the fabrication of thin RPDs. Material and methods: Tensile bars were manufactured using cast metal-ceramics (C-MC group), RPD alloys (C-RPD group), and SLM Co-Cr metal-ceramic alloys. The SLM specimens were subjected to 2 different heat treatments, L1 at 880°C and L2 at 1100°C, and were further divided into subgroups (L1-MC, L1-RPD, L2-MC, and L2-RPD). Thirty-six tensile specimens were prepared in C-RPD, L1-RPD, and L2-RPD (simulated partial denture alloys for clinical use) and in C-MC, L1-MC, and L2-MC (simulated metal-ceramic alloys); 18 metal-ceramic bond strength specimens were prepared in C-MC, L1-MC, and L2-MC groups (n=6). The tensile test and 3-point bend test were conducted using a universal testing machine. The fracture surfaces of the L2-RPD tensile bar were examined using a scanning electron microscope. The Student t test (α=.05) was used for statistical analysis. Results: No significant differences were observed between the bond strengths of L1-MC and C-MC (P=.74) or between those of L2-MC and C-MC (P=.124). The 0.2% yield strength (σ0.2) and elongation of all SLM specimens exceeded the minimum requirements required for the fabrication of thin RPDs as prescribed in ISO 22674:2016. The σ0.2 value of L1-MC and L2-MC was significantly higher than that of C-MC. Significant differences in σ0.2 values were found among the 3 RPD groups, L1-RPD>L2-RPD>C-RPD. For the elongation, significant differences were found among the 3 groups, L2-RPD>C-RPD>L1-RPD. The fracture surface of L2-RPD showed clear submicroscale dimples with fusion defects. Conclusions: When Co-Cr metal copings and RPD frameworks were fabricated on the same substrate simultaneously using SLM, heat treatment at 1100°C was found more suitable than at 880°C to release residual stress, considering the toughness required for dental prostheses.

Effects of Cemented Hip Stem Pre-heating on Stem Push-out Strength

The effect of stem surface treatment and material on pistoning of ulnar components in linked cemented elbow prostheses

Pure Alumina Bearings with Cementless Stems Versus Sandwich Bearings with Cemented Stems in Total Hip Arthroplasty.

Influence of Femoral Stem Surface Finish on the Apparent Static Shear Strength at the Stem–cement Interface

The Biomechanical Study of Intertrochanic Fractures Treated with Cemented Femoral Stem

Initial Damage Analysis in Bone Cement-Stem Debonding Procession of Cemented Hip Arthropsty

Effects of Low-Frequency Pulsed Wave Ultrasound on the Shear Properties of the Interface of Vancomycin-Loaded Acrylic Bone Cement-Stem

Risk factors for periprosthetic femoral fracture risk around a cemented polished taper-slip stem using an osteoporotic composite bone model

Analysis of Femoral Components of Cemented Total Hip- Arthroplasty

Effects of Materials of Cementless Femoral Stem on the Functional Adaptation of Bone

Bond Strength Analysis of the Bone Cement-Stem Interface of Hip Arthroplasties

Comparison of Early Postoperative Stress Distribution around Short and Tapered Wedge Stems in Femurs with Different Femoral Marrow Cavity Geometries Using Finite Element Analysis

Strain distribution in the proximal human femur after insertion of CF/PEEK femoral stems

A comprehensive analysis of bio-inspired design of femoral stem on primary and secondary stabilities using mechanoregulatory algorithm

Static shear strength between polished stem and seven commercial acrylic bone cements

Investigation Of Protein Adsorption Mechanism And Biotribological Properties At Simulated Stem-Cement Interface

Consequences of Using Poly-Ether-ether-ketone Versus Traditional Implant on Tibial Cement Penetration and Short-Term Clinical Outcomes During Total Knee Arthroplasty: a Randomized Controlled Trial.

The influence of stem length and fixation on initial femoral component stability in revision total knee replacement

Experimental and numerical analysis of the mechanical behavior of bone cement reinforced with alumina particles

Comparative analysis of the biomechanical behavior of two different design metaphyseal-fitting short stems using digital image correlation

Effect of two heat treatments on mechanical properties of selective-laser-melted Co-Cr metal-ceramic alloys for application in thin removable partial dentures