Abstract:Background: For the treatment of bone defects that exceed the critical size of the injury, several therapies have been investigated. Thermal decomposition method is suggested for extraction of natural hydroxyapatite bioceramic (HA). This technique in comparison with other methods of producing HA, has less complexity and greater economic efficiency. Objective: In the present study, a thermal decomposition method is suggested for extraction of natural HA from bovine femur bones. Methods: In this experiment, to extract the ceramic material, the bone samples were first de-fatted and ground to particles less than 420 μm, and also 420-500 μm, respectively. Prepared powders were heated at 170 °C for 24 h, and then divided into two groups for 6 h. The first group was heated at 750 °C; the second group was heated at 850 °C. The calcium phosphate compounds were obtained with complete elimination of the organic phase of the bone. These bioceramic compounds were characterized physiochemically by X-ray diffraction (XRD), fourier transform infrared spectroscopy (FTIR), energy dispersive X-ray (EDX), and scanning electron microscopy (SEM). Results: We found that the powder heated at 750 °C in two dimensional scales was rich in carbonated hydroxyapatite, and therefore, eminently suitable for using in hard tissue replacements. However, increasing the temperature up to 850 °C reduced the Ca/P ratio to 1.5 in the powder sample sizes less than 420 μm. Consequently, the obtained composition became rather similar to the chemical formula of tricalcium phosphate (TCP) that is appropriate in tissue engineering and drug delivery applications. Conclusion: The observations affirmed that by eliminating the collagen and other organic materials existing in the bovine bones, the mineral phase of the bone had the potential of transformation to nano-particles. To investigate the repair of critical-size bone defects and bone augmentation, cylindrical blocks were fabricated by applying different pressures of 150, 160 and 170 MPa. The structure and compressive strength of the pressed samples after sintering at 1200 °C were characterized by SEM and compressive strength test.

Thermomechanical method for cement extraction in revision arthroplasty

Thermal Evaluation of the Injectable Liquid Metal Bone Cement in Orthopedic Treatment

Rheological and Curing Behavior of a Newly Developed, Medium Viscous Acrylic Bone Cement

An experimental study of heat adaptation of bioabsorbable craniofacial meshes and plates

Forensic Exploration of Endodontic Cements: Unveiling Macroscopic and Radiographic Changes Under High Temperatures

Effects of Cemented Hip Stem Pre-heating on Stem Push-out Strength

Liquid-solid phase transition alloy as reversible and rapid molding bone cement

Preparation and Characterization of Low Temperature Heat-Treated 45S5 Bioactive Glass-Ceramic Analogues

Modification of polymethylmethacrylate bone cement with halloysite clay nanotubes

Rheological Analysis and Evaluation of Measurement Techniques for the Curing Polymethylmethacrylate Bone Cement in Vertebroplasty

Experimental Cremation of Bone: Crystallite Size and Lattice Parameter Evolution

Effect of commonly used lavage solutions on the polymerization of bone cement

Effect of operating parameters on the removal of bone cement by a sawing process

Fabrication of a hard tissue replacement using natural hydroxyapatite derived from bovine bones by thermal decomposition method

Experimental and numerical analysis of the mechanical behavior of bone cement reinforced with alumina particles

A Self-healing PMMA Bone Cement: Influence of Crystal Size of Grubbs’ Catalyst

Influence of elevated temperature on the microstructures and mechanical properties of cement-based mortar with sands and refractory materials

An overview of the heat-induced changes of the chemical composition of bone from fresh to calcined

Thermal analysis of tendon, cartilage and bone samples from shoulder joint replacement patients using differential scanning calorimetry (DSC) and thermogravimetry (DTA/TG)

Analgesic eluting bone cement: A novel approach for targeted pain management in total knee arthroplasty - An in-vitro study

The effects of high temperature heating on the gas permeability and porosity of a cementitious material