Abstract:All ultra-wideband (UWB) sensor applications require hardware designed directly for their specific application. The switching of broadband radio frequency and microwave signals is an integral part of almost every piece of high-frequency equipment, whether in commercial operation or laboratory conditions. The trend of integrating various circuit structures and systems on a chip (SoC) or in a single package (SiP) is also related to the need to design these integrated switches for various measuring devices and instruments in laboratories, paradoxically for their further development. Another possible use is switching high-frequency signals in telecommunications devices, whether mobile or fixed networks, for example, for switching signals from several antennas. Based on these requirements, a high-frequency semiconductor integrated switch with NMOS transistors was designed. With these transistors, it is possible to achieve higher integration than with bipolar ones. Even though MOSFET transistors have worse frequency characteristics, we can compensate them to some extent with the precise design of the circuit and layout of the chip. This article describes the analysis and design of a high-frequency semiconductor integrated switch for UWB applications consisting of three series-parallel switches controlled by CMOS logic signals. They are primarily intended for UWB sensor systems, e.g., when switching and configuring the antenna MIMO system or when switching calibration tools. The design of the switch was implemented in low-cost 0.35 μm SiGe BiCMOS technology with an emphasis on the smallest possible attenuation and the largest possible bandwidth and isolation. The reason for choosing this technology was also that other circuit structures of UWB systems were realized in this technology. Through the simulations, individual parameters of the circuit were simulated, the layout of the chip was also created, and the parameters of the circuit were simulated with the parasitic extraction and the inclusion of parasitic elements (post-layout simulations). Subsequently, the chip was manufactured and its parameters were measured and evaluated. Based on these measurements, the designed and fabricated UWB switch was found to have the following parameters: a supply current of 2 mA at 3.3 V, a bandwidth of 6 GHz, an insertion loss (at 1 GHz) of −2.2 dB, and isolation (at 1 GHz) of −33 dB, which satisfy the requirements for our UWB sensor applications.

Signal Processing for Wireless Communication MIMO System with Nano- Scaled CSDG MOSFET based DP4T RF Switch

A 100mhz-2ghz Wireless Receiver In 40-Nm Cmos For Software-Defined Radio

A CMOS SPDT RF Switch with 68 Db Isolation and 1.0 Db Loss Feathering Switched Resonance Network for MIMO Applications

The Design of a 57-65Ghz SPDT Switch with LC Resonant Techniques in 40 Nm CMOS Process

A Silicon Optical Single Sideband Modulator with Ultra-High Sideband Suppression Ratio

Analytical Surface Potential Modelling-Based Small Signal Analysis and RF Performance Characterization of DMG SOI MOSFET for Better RFIC Application

Efficient DSP and Circuit Architectures for Massive MIMO: State-of-the-Art and Future Directions

A CMOS Dual Band Low-Loss High-Isolation Switch for 5G New Radio.

RF MOSFET: recent advances, current status and future trends

Analysis and Implementation of Controlled Semiconductor Switch for Ultra-Wideband Radar Sensor Applications

Si 3 N 4 -Based Integrated Optical Analog Signal Processor and Its Application in RF Photonic Frontend

An Advanced Real Time Lead RF-MEMS Based Switch Design for AI Applications

Improved analog and AC performance for high frequency linearity based applications using gate-stack dual metal (DM) nanowire (NW) FET (4H-SiC)

Ultra Low Loss and High Linearity RF Switch Using 130nm SOI CMOS Process

Design and Analysis of a 28 GHz T/R Front-End Module in 22-nm FD-SOI CMOS Technology

MOSFET Based Absorber for Reflected Signal in 5G Massive MIMO Base Station - A Circuit Perspective

Rf Mems Switch and Its Applications

The Impact of Semiconductor Technology Scaling on CMOS RF and Digital Circuits for Wireless Application

A DC-10GHz SPDT RF Switch with Bulk Self-Biasing Technique in 0.25µm BiCMOS Process

Design, simulation and analog/RF performance evaluation of a hetero-stacked source dual metal T-shaped gate tunnel-FET in thermally variable environments

Nanoscale modeling of an efficient Carbon Nanotube-based RF switch using XG-Boost machine learning algorithm