Abstract:Journal of Composite Materials, Ahead of Print. This study presents an investigation into mechanical and thermal properties, as well as the microstructure of Automated Fiber Placement-manufactured laminates using a novel carbon fiber-reinforced low-melt polyaryl ether ketone polymer material. The material's lower melting temperature and lower melt viscosity as compared to established high-temperature thermoplastic materials as PEEK, promises favourable characteristics for the Automated Fiber Placement process. This work aims at in-situ consolidation and the influence of a heated tooling and a post process tempering step, which both turned out to be promising in previous investigations. Laminates were manufactured using a cold tooling, a heated tooling configuration, a cold tooling with a subsequent tempering process step and a hot-pressed reference laminate. Differential Scanning Calorimetry showed that crystallinity values more than doubled for the heated tooling and post process tempering configurations, compared to the cold tooling, reaching 24% and 30%, respectively. Mechanical strength values showed an increase in interlaminar shear strength and compression strength but did not increase to the same extent as was expected from the increase in crystallinity. With Scanning Electron Microscopy differences in the microscopic structure of the polymer matrix could be detected. While the post process tempering step leads to a mostly lamellar crystalline structure, the heated tooling configuration and the post process hot pressing induce a predominance of crystalline spherulites, which might positively affect the mechanical performance. Computed Tomography scans revealed a high amount of porosity in the in-situ-manufactured samples and unprocessed tape material, which likely mitigated the positive effect of increased crystallinity.

Significantly enhanced laser trapping and heating of carbon nanotube/carbon fibre hierarchical composites for efficient laser-assisted automated fibre placement

Carbon nanotube-induced localized laser heating toward simultaneously enhanced laydown efficiency and fracture toughness of in-situ consolidated glass fiber thermoplastic composites

Optical properties optimization of carbon fiber reinforced thermoplastic tapes by micro surface texturing for enhanced laser heating efficiency and in-situ consolidation quality during AFP process

Mechanism and Behavior of Laser Irradiation on Carbon Fiber Reinforced Polyetheretherketone (CF/PEEK) During the Laser-Assisted In-Situ Consolidation Additive Manufacturing Process

Carbon nanotube film engineered fiber reinforced polymer composites

Consolidation of aerospace-grade high-temperature thermoplastic carbon fiber composites via Nano-engineered electrothermal heating

Effect of crystallinity on optical properties of PEEK prepreg tapes for laser-assisted automated fiber placement

Preparation of MWCNTs/CF/PEEK Multi-Scale Composites with Good Mechanical and Electrical Conductivity by a Two-Step Process of AFP and Out-of-autoclave Tempering

A Novel Continuous Carbon Nanotube Fiber/carbon Composite by Electrified Preform Heating Chemical Vapor Infiltration

Robot-assisted laser additive manufacturing for high-strength/low-porosity continuous fiber-reinforced thermoplastic composites

In situ consolidation process-based fabrication and interlaminar modification mechanism associated with CF/PEEK multiscale nanocomposites characterized by interlaminar doping of CNTs

The effect of nanoparticle fillers on glass fiber/poly‐ether‐ether‐ketone prepreg laser absorbance, thermal conductivity and interlayer performance

Research progress on laser processing of carbon fiber-reinforced composites

An integrated nanofiller spray and nanosecond pulse electrically-assisted method for synergistically interlaminar toughening and in-situ damage monitoring of CFRP composites

Ultrafast printing of continuous fiber‐reinforced thermoplastic composites with ultrahigh mechanical performance by ultrasonic‐assisted laminated object manufacturing

Layer-by-layer grafting CNTs onto carbon fibers surface for enhancing the interfacial properties of epoxy resin composites

Interlayer bonding improvement of PEEK and CF-PEEK composites with laser-assisted fused deposition modeling

Development of Laser Processing Carbon-Fiber-Reinforced Plastic

Characteristics of in-situ automated fiber placement carbon-fiber-reinforced low-melt polyaryl ether ketone laminates part 1: Manufacturing influences

Laser-assisted AFP-TPC Manufacturing of CF/PEEK High-Performance Thermoplastic Composites with Low Warpage-Deformation Defects

Investigations on 355 nm picosecond laser machining of carbon fiber reinforced polymer composites