Abstract:This study investigated the effect of adding La–Ce mixed rare earths and Sr on the microstructure and mechanical properties of AlSi10MnMg alloy. The experiment utilized different combinations of modifiers, including single La–Ce rare earths, single Sr, and the combined addition of La–Ce mixed rare earths and Sr. This study compared their effects on grain refinement, the modification of the α-Al phase and eutectic silicon phase, and tensile properties and hardness. The results showed that the combined modification of Sr and mixed rare earth elements significantly refined the grains, optimized the morphology of the α-Al phase and eutectic silicon phase, and improved the overall mechanical properties of the aluminum alloy. Under the combined modification, the addition of 0.02 wt.% Sr and 0.1 wt.% RE (La–Ce mixed rare earths) exhibited the most pronounced refining effect. The secondary dendrite arm spacing (SDAS) was reduced by 59.18%. The eutectic silicon phase transformed from coarse needle-like shapes to fine fibrous or granular forms, with an aspect ratio reduction of 69.39%. Meanwhile, the alloy's tensile strength and hardness were significantly improved. The tensile strength increased to 240 MPa, achieving an increase of 23.08%; the yield strength increased to 111 MPa, achieving an increase of 18.09%; and the elongation reached 7.3%, achieving an increase of 73.81%. This indicates that the proper addition of Sr and mixed rare earths can significantly optimize the microstructure and enhance the mechanical properties of AlSi10MnMg alloy, providing an effective method for the preparation of high-performance heat-treatment-free aluminum alloys.

Synergistic effect of Gd and Sr on the microstructure and mechanical properties of Al–Si–Mg alloy

Effects of solid solution and aging process on microstructure and mechanical properties of Mg-Gd-Y alloy

The Influence of the Combined Addition of La–Ce Mixed Rare Earths and Sr on the Microstructure and Mechanical Properties of AlSi10MnMg Alloy

Effects of Sr on Microstructure and Mechanical Properties of Mg-9al-1si-0.3zn Alloy

Effect of Ti Addition on the Microstructure and Mechanical Properties of Cast Mg-Gd-Y-Zn Alloys

Modification mechanism and tensile property of Al-9Si-0.4Mg-0.1Cu alloy

Effect of Ti and Sr on the microstructure and mechanical properties of Al-12Si-4.5Cu-2Ni alloy

Effect of Al-Sr-Y intermediate alloy on microstructure and mechanical properties of A356 alloy

Microstructure and Mechanical Properties of Mg–9Li–3Al–xGd Alloys

Effects of the Simultaneous Addition of Gd and Mn on the Microstructures and Mechanical Properties of Mg-Bi Alloys

Effects of Zr and Sr on microstructure and mechanical properties of cast Al–Si–Cu–Ni–Mg alloy

Effect of Sr on Microstructure and Strengthening Mechanism of Al-4.6Mg Alloy

Effect of Sr Modification on the Microstructures, Mechanical Properties, and Thermal Conductivity of Hypoeutectic Al-13.6Cu-6Si Alloys

Effect of Yttrium Addition on Microstructure and Mechanical Properties of Sr-Modified Low-Si Cast Aluminum Alloy

Effect of Sr and Nd on Microstructure and Mechanical Properties of AZ91-1Si Alloy

Study on the Mutual Effect of La and Gd on Microstructure and Mechanical Properties of Mg-Al-Zn Extruded Alloy

Interfacial microstructure, mechanical properties and strengthening mechanism of Mg/Al bimetallic composites produced by a novel compound casting with the addition of Gd

Microscopic mechanism of mechanical property improvement of the casted Al-7Si-0.4Mg-0.3Y alloy

Synergistic Effect of Strontium and Melt Quenching on the Solidification Microstructure of Hypereutectic Al-Si Alloys

Effect of Cu and Sr on the Microstructure and Mechanical Properties of Al-Mg-Si Based Alloy Sheets

Investigating the role of Cu, Zr and V on the evolution of microstructure and properties of Al-Si-Mg cast alloys