Abstract:The dense WC-M2 high-speed steel matrix composites (WC-M2 HSS MMCs) with different WC content were prepared by mechanical alloying and vacuum sintering process. Tungsten Carbide (WC) with 0, 2, 5, 8, and 10 (by weight %) were dispersed in the matrix. The effects of WC content on the densification mechanism, phase composition, microstructure, fracture morphology, and mechanical and wear properties of the sintered composites were systematically investigated. The experimental results showed that at a vacuum sintering temperature of 1260 °C, the composite material specimens achieved near-full densification, with predominant phases being Martensitic, M 7 C 3 , M 6 C, M 2 C, MC, WC, α-Fe, and γ-Fe. Reasonable WC addition has improved grain uniformity and reduced micro-defects, which enhanced the overall mechanical properties. With an increase in WC content, the hardness and relative density of the composites showed a gradual increase, whereas transverse rupture strength and impact toughness initially improved but subsequently decreased. The friction coefficient displayed an initial increase followed by a decrease, while the wear rate showed an opposite trend. The impact fracture morphology is dominated by the interfacial separation between the WC particle phase and the binder phase, supplemented by the plastic tearing of the binder phase. The impact toughness mainly depended on the fracture of the binder phase. During crack propagation, both intergranular and transgranular fractures exist, of which the intergranular fracture prevails and coarse grains are more prone to transgranular fracture. With 5 wt.% WC, the steel matrix composites obtained peak mechanical performance, with impact toughness, bending strength, and hardness measuring 13.2 J cm −2 , 1584.3 MPa, and 780.9 HV, respectively, which also yielded the highest wear resistance.

Microstructure, High-Temperature Wear, and Corrosion Behaviors of UNS R56320-xWC Composite Fabricated through Powder Metallurgy

Microstructure and Corrosion Behaviour of WC-Co Coating Fabricated by Plasma Arc Welding

Influences of Ni/Cu/Cr3C2 Composite Additive on Microstructure and Properties of WC–10Co Fine Grained Hardmetal

Microstructural and Tribological Resistance of Flame-Sprayed CoMoCrSi/WC-CrC-Ni and CoMoCrSi/WC-12Co Composite Coatings Remelted by Microwave Energy

Effect of Tungsten Carbide Additions on the Microstructure, Mechanical, and Tribological Properties of M2 High-Speed Steel Matrix Composites

A novel approach to fabricate WC reinforced W Cu composites via MSC and infiltration method

Microstructure evolution and tribological behavior of laser cladded Al 1.8 CrCuFeNi 2 /WC composite coatings on Ti-6Al-4 V

Microstructure and high-temperature oxidation behavior of Ti3AlC 2/W composites

Enhancing Tribological Performance of SS-316 Through Microwave Cladding of NiCr-Cr3C2 Composite: Fabrication, Characterization, and Optimization

Microstructural Effects of Y2O3 and TiC Additions in Tungsten

Mechanical and tribological behaviour of tungsten carbide reinforced aluminum LM4 matrix composites

Influence of WC-12Co reinforcement on sliding wear performance of stainless steel-based MMC processed in a microwave oven

Investigation on the mechanical and tribological behavior of tungsten-reinforced Ti-5Al-2.5Sn composites

Erosion behavior of Al–SiC and Al–WC MMCs via powder metallurgy under solid particle impingement

Microstructure and wear resistance of in-situ synthesized stellate Mo2C reinforced WC/amorphous composite coatings by resistance seam welding (RSW)

Effect of Percentage Variation on Wear Behaviour of Tungsten Carbide and Cobalt Reinforced Al7075 Matrix Composites Synthesized by Melt Stirring Method

Spark Plasma Sintering Preparation of Tungsten Carbide-Reinforced Iron-Based Composite Materials: Wear Resistance Performance and Mechanism

Development and characterization of multiwalled carbon nanotube-reinforced microwave sintered hybrid aluminum metal matrix composites: An experimental investigation on mechanical and tribological performances

Microstructural evolution and performance analysis of WC-11Co reinforced iron matrix composites

DRY AND HOT CORROSION BEHAVIOUR OF Al-Ni-Co-x MWCNT COMPOSITES PROCESSED THROUGH POWDER METALLURGY

Enhanced mechanical and tribological properties of ultrasonically assisted stir-cast AA7075 metal matrix composites in challenging corrosive environments