Abstract:A novel method for calculating the critical resolved shear stress (CRSS) ratios of different deformation system types in polycrystalline non-cubic metals has been developed. The mean CRSS ratios between different deformation systems were calculated for both commercially pure (CP) Ti and Ti–5Al–2.5Sn (wt.%) tensile deformed at ambient temperature and 455°C using an in situ scanning electron microscope-based testing technique combined with electron backscattered diffraction. It was found that the relative activity of the different deformation systems changes as a function of alloying composition and deformation temperature. Prismatic slip was the most active deformation mode for CP Ti. CP Ti exhibited a lower resistance to prismatic slip at both ambient and elevated temperatures compared with Ti–5Al–2.5Sn. For Ti–5Al–2.5Sn, prismatic slip was the most active deformation system at ambient temperature although the basal slip activity significantly increased compared to CP Ti, mostly likely due to an increased c/a ratio resulting in a closer packed basal plane. At 455°C, basal slip exhibited a lower CRSS than prismatic slip for Ti–5Al–2.5Sn. The relative activity of other deformation systems was also affected by alloying and temperature. The statistical resampling technique of bootstrapping was used to generate multiple equivalent data sets from which mean CRSS ratios between different deformation systems, and associated confidence intervals, could be deduced. It was found that the mean CRSS ratios at low and high strains varied slightly for the same testing conditions. Moreover, lesser activated slip systems resulted in relatively larger confidence intervals for the CRSS means. This variability may be attributed to a number of potential factors, including measurement errors, rotations of grains during deformation, local stress state variations, and work hardening. The analysis further suggests that awareness of the intrinsic statistical variability in CRSS ratios should be considered when formulating crystal plasticity constitutive models.

Comment on "Effects of shear methods on shear strengths and deformation modes of two typical transition metal carbides and their unification"

Instability Analysis and Rate-Dependent Failure Criteria for Adiabatic Shear Band Propagation of Ti-6al-4v

Modeling the Strain Rate-Dependent Constitutive Behavior in Nanotwinned Polycrystalline Metals

Modern experimental verifications of shear mechanism of martensitic transformation and calculation of shear energy——Comment on "non-shear mechanism of martensitic transformation" again

The influence of transition metal solutes on dislocation core structure and values of Peierls stress and barrier in tungsten

Development of Multi-Scale Computation Framework to Investigate the Failure Behavior of the Materials

A Constitutive Description of the Yield Strength and Strain Hardening Behaviors of Nano-Twinned Metals

Pure shear deformation and its induced mechanical responses in metallic glasses

Erratum To: Temperature Effects on Deformation and Serration Behavior of High-Entropy Alloys (Heas)

Response to Comment on "Cryoforged nanotwinned titanium with ultrahigh strength and ductility"

Comparison of Critical Shear Strain Evaluations for Simple Shear Test

Nanostructure-property Relation of Σ5 Grain Boundary in HfNbZrTi High-Entropy Alloy under Shear

Decoupling of Strain and Temperature Effects on Microstructural Evolution During High Shear Strain Deformation

Critical resolved shear stresses for slip and twinning in Mg-Y-Ca alloys and their effect on the ductility

The Nano- And Mesoscopic Cooperative Collective Mechanisms Of Inhomogenous Elastic-Plastic Transitions In Polycrystalline Tini Shape Memory Alloys

Tensile and shear loading of four fcc high-entropy alloys: A first-principles study

Extreme shear-deformation-induced modification of defect structures and hierarchical microstructure in an Al–Si alloy

Mechanical response and grain boundary behavior of (HfNbTaTiZr)C high-entropy carbide ceramics and its constituent binary carbides

Atomistic Simulations of Ductile Failure in a b.c.c. High-Entropy Alloy

Theoretical and Experimental Study of Phase Transformation and Twinning Behavior in Metastable High-Entropy Alloys

Methodology for estimating the critical resolved shear stress ratios of α-phase Ti using EBSD-based trace analysis