Abstract:BackgroundTin and its compounds can cause serious harm to human respiratory system and nervous system, but there is no corresponding national standard method for the determination of tin in PM2.5. ObjectiveTo establish a method for the determination of tin and its compounds in PM2.5 by atomic fluorescence spectrometry (AFS) after ultrasonic extraction with concentrated hydrochloric acid. MethodsWe extracted a fixed volume of air at a constant speed through a sampler with preset cutting characteristics to trap PM2.5 in the ambient air on quartz filter membranes. By selecting extraction solvent, comparing extraction temperature and time, and adjusting the acidity of solution to be measured, the sample pretreatment process was optimized, and a method for the determination of tin and its compounds in PM2.5 by AFS was proposed, and its performance indexes such as linearity, detection limit, and lower limit of quantification were obtained. The accuracy and precision of the method were evaluated by the standard addition recovery test with blank quartz filter membranes, and the interference test was carried out by adding standard urban particulate samples. The proposed method and the method recommended by the “Handbook on Monitoring and Protection of Air Pollution (Haze) Effects on Population Health (2020)” (the Handbook) were applied to actual samples, and the results were compared. ResultsThis experiment used concentrated hydrochloric acid as the extraction solvent. The higher the reaction temperature and the longer the reaction time, the higher the recovery rate. Therefore, 70 ℃ water bath ultrasonic extraction for 3 h was selected. In terms of the proposed method, the linear range of detection was from 5.00 μg·L−1 to 50.00 μg·L−1, with a correlation coefficient ≥0.999 and a detection limit of 0.27 μg·L−1. When the quantitative detection of the lower limit was 0.90 μg·L−1，and the sampling volume was 144 m3, the limit of quantification was 1.25 ng·m−3. The recovery rate of standard addition of blank quartz filter membranes was 94.1%-97.5%, with a relative standard deviation ≤3.2%; the recovery rate of standard addition of standard urban particulate matter samples was 93.5%-103.0%, and the relative standard deviation was ≤2.1%, indicating that coexisting components in PM2.5 samples would not affect the determination of tin. For the 10 quartz filter membrane samples of PM2.5 monitoring, the results of tin by the established method (extraction with concentrated hydrochloric acid) were higher than those of the Handbook recommended method (extraction with nitric acid), and the difference is (3.61±0.54) ng·m−3(t=21.303, P<0.05). ConclusionThe established method for the determination of tin and its compounds in PM2.5 by AFS after ultrasonic extraction with concentrated hydrochloric acid is simple, accurate, and suitable for laboratory determination of tin and its compounds in large quantities of PM2.5 samples.

Direct determination of tin in whole blood and urine by GF AAS

The Determination of Trace Amounts of Tin by Flow-Injection Hydride Generation Atomic-Absorption Spectrometry with On-Line Ion-Exchange Separation and Preconcentration.

Adsorptive Stripping Differential Pulse Voltammetric Determination of Trace Amounts of Tin in Biological Samples

Determination of trace amounts of tin by hydride generation direct current plasma atomic emission spectrometry: interference reduction by L-cystine

Determination of Trace Tin by Anodic Stripping Voltammetry at A 1-(3-nitrophenyl)-3-(4-phenylazophenyl)triazen Modified Carbon Paste Electrode

Determination of tin and its compounds in ambient PM2.5 by atomic fluorescence spectrometry after ultrasonic extraction with concentrated hydrochloric acid

Determination of Germanium and Tin and Inorganic Tin Species by Hydride Generation in Situ Trapping Flame Atomic Absorption Spectrometry

Preconcentration by coprecipitation of arsenic and tin in natural waters with a Ni-pyrrolidine dithiocarbamate complex and their direct determination by solid-sampling atomic-absorption spectrometry

Simultaneous Determination of Ultra-trace Pt, Pd, Rh and Ir in Geochemical Samples by Inductively Coupled Plasma Mass Spectrometry Following Tin Fire Assay Preconcentration and Microwave Digestion

Determination of total chromium in whole blood, blood components, bone, and urine by fast furnace program electrothermal atomization AAS and using neither analyte isoformation nor background correction

Determination of total Sn in some canned beverages by FAAS after separation and preconcentration

Highly Efficient Photochemical Vapor Generation for Sensitive Determination of Trace Inorganic Tin by Inductively Coupled Plasma Mass Spectrometry

Semi-automatic determination of tin in marine materials by continuous flow hydride generation inductively coupled plasma atomic emission spectrometry

Validation of a method to quantify chromium, cadmium, manganese, nickel and lead in human whole blood, urine, saliva and hair samples by electrothermal atomic absorption spectrometry

Investigation of Organic Phase Chemical Vapor Generation-Atomic Fluorescence Spectrometry in the Determination of Tin

Elimination of matrix and spectral interferences in the measurement of lead and cadmium in urine and blood by electrothermal atomic absorption spectrometry with deuterium background correction

Current perspectives in analyte extraction strategies for tin and arsenic speciation

[Determination of thallium in the urine with colloidal palladium as the matrix modifier by graphite furnace atomic absorption Spectrometry]

Determination of hydride-forming elements in high purity coppers by inductively coupled plasma atomic emission spectrometry

Determination of trace tin by solid substrate-room temperature phosphorimetry using sodium dodecyl sulfate as sensitizer.

Determination of Pt in biological samples by inductively coupled plasma atomic emission spectrometry (ICP-AES) with electrothermal vaporization (ETV)