Abstract:Microstructure, mechanical performance and wall thickness of long glass fiber‐reinforced polypropylene pipes formed via fluid‐assisted co‐injection molding. Fluid‐assisted co‐injection molding (FACIM) processes can be divided into water‐assisted co‐injection molding (WACIM) and gas‐assisted co‐injection molding (GACIM) processes. This study focuses on evaluating the quality of pipes formed through four distinct processes: water‐assisted co‐injection molding overflow (WACIM‐O), water‐assisted co‐injection molding short shot (WACIM‐S), gas‐assisted co‐injection molding overflow (GACIM‐O), and gas‐assisted co‐injection molding short shot (GACIM‐S). Wall thickness, wall thickness uniformity, fiber morphology, and pressure resistance were studied. Long glass fiber‐reinforced polypropylene was the outer layer while polypropylene was the inner layer. The total wall thickness of the four types of pipes tends to decrease along the flow direction; however, the total wall thickness of the short‐shot pipes increases at the end. The wall thickness uniformity of the GACIM pipes is better than that of the WACIM pipes while the average fiberglass fracture length of the FACIM‐O pipes is longer than that of the FACIM‐S pipes. Also, the average fiber fracture length of the WACIM‐O pipes is the longest. The fiber orientation distribution can be divided into the near‐mold wall layer, the outer core layer, and the near‐interface layer. The degree of fiber orientation increases layer by layer along the flow direction. Glass fiber orientation is the highest for the WACIM‐O pipes; the pressure resistance of FACIM‐O pipes is better than that of the FACIM‐S pipes. Highlights Pipes were successfully prepared from long glass fiber‐reinforced polypropylene and polypropylene as the material. The wall thickness uniformity of the fluid‐assisted co‐injection molding (FACIM)‐overflow pipes is satisfactory. The total wall thickness of the FACIM‐short shot pipes have notable variations. The water‐assisted co‐injection molding‐overflow pipes present a longer average fiber breaking length. The pressure resistance of FACIM‐overflow pipes is better than that of FACIM‐short shot pipes.

Research on the quality of long glass fiber‐reinforced polypropylene pipes formed via fluid‐assisted co‐injection molding

The Investigation of Overflow Water-Powered Projectile-Assisted Injection Molded Short-Glass-Fiber-Reinforced Polypropylene

Formation mechanism of high‐pressure water penetration induced fiber orientation in overflow water‐assisted injection molded short glass fiber‐reinforced polypropylene

Preparation of glass fiber reinforced phenolic injection molding materials and its properties

Simulation and Experimental Analysis on Non-circular Cross-section Parts Residual Wall Thickness of Water-assisted Injection Molding

Effects of Processing Method and Parameters on the Wall Thickness of Gas-Projectile-Assisted Injection Molding Pipes

Numerical and experimental investigations on the mechanism of flow‐induced fiber orientation in short‐shot water‐assisted injection‐molded short‐glass‐fiber‐reinforced polypropylene

The study of short‐shot water‐assisted injection molding of short glass fiber reinforced polypropylene

Experimental and numerical investigations on formation mechanisms of hollow structures in overflow water‐assisted injection‐molded parts of short‐glass‐fiber‐reinforced polypropylene

Direct In-Mold Impregnation of Glass Fiber Fabric by Polypropylene with Supercritical Nitrogen in Microcellular Injection Molding Process

Influence of Processing Conditions on the Morphological Structure and Ductility of Water-Foamed Injection Molded PP/LDPE Blended Parts

Visualization Analysis of Defibration and Distributive Uniformity of Fibers in Long-fiber-reinforced, Injection-Molded Resins

Pultrusion molding of continuous fiber reinforced thermoplastic composite pipe using partially-impregnated commingled yarns

The combined effect of impregnated rollers configuration and glass fibers surface modification on the properties of continuous glass fibers reinforced polypropylene prepreg composites

Effect of high quality hybrid coatings and coating condition on the properties of continuous glass fiber reinforced polypropylene prepreg composites

Experimental analysis of fluid‐assisted injection molding of pipe fittings with different angles by short‐shot method

Numerical Simulation on the Penetration Behavior of the Projectile during the Water Injection Stage of Water-Projectile-Assisted Injection Molding Process

Improving the interfacial shear strength of polypropylene/carbon fiber nonwoven composite by three different methods

Effects of fabrication method of composite yarn intermediate material and resin melt viscosity on the impregnation properties and mechanical properties of PA66 fiber and glass fiber composites

Effect of fibre concentration on the mechanical properties of welded reinforced polypropylene

Crystal morphology and tensile properties of LLDPE containing PP fibers as obtained via dynamic packing injection molding