Abstract:Microstructure, mechanical performance and wall thickness of long glass fiber‐reinforced polypropylene pipes formed via fluid‐assisted co‐injection molding. Fluid‐assisted co‐injection molding (FACIM) processes can be divided into water‐assisted co‐injection molding (WACIM) and gas‐assisted co‐injection molding (GACIM) processes. This study focuses on evaluating the quality of pipes formed through four distinct processes: water‐assisted co‐injection molding overflow (WACIM‐O), water‐assisted co‐injection molding short shot (WACIM‐S), gas‐assisted co‐injection molding overflow (GACIM‐O), and gas‐assisted co‐injection molding short shot (GACIM‐S). Wall thickness, wall thickness uniformity, fiber morphology, and pressure resistance were studied. Long glass fiber‐reinforced polypropylene was the outer layer while polypropylene was the inner layer. The total wall thickness of the four types of pipes tends to decrease along the flow direction; however, the total wall thickness of the short‐shot pipes increases at the end. The wall thickness uniformity of the GACIM pipes is better than that of the WACIM pipes while the average fiberglass fracture length of the FACIM‐O pipes is longer than that of the FACIM‐S pipes. Also, the average fiber fracture length of the WACIM‐O pipes is the longest. The fiber orientation distribution can be divided into the near‐mold wall layer, the outer core layer, and the near‐interface layer. The degree of fiber orientation increases layer by layer along the flow direction. Glass fiber orientation is the highest for the WACIM‐O pipes; the pressure resistance of FACIM‐O pipes is better than that of the FACIM‐S pipes. Highlights Pipes were successfully prepared from long glass fiber‐reinforced polypropylene and polypropylene as the material. The wall thickness uniformity of the fluid‐assisted co‐injection molding (FACIM)‐overflow pipes is satisfactory. The total wall thickness of the FACIM‐short shot pipes have notable variations. The water‐assisted co‐injection molding‐overflow pipes present a longer average fiber breaking length. The pressure resistance of FACIM‐overflow pipes is better than that of FACIM‐short shot pipes.

Visualization Analysis of Defibration and Distributive Uniformity of Fibers in Long-fiber-reinforced, Injection-Molded Resins

INTEGRATED SIMULATION OF MELT FLOW, FIBER FRACTURE AND FIBER ORIENTATION FOR FIBER REINFORCED PLASTICS IN INJECTION MOLDING

Simulation of Fiber Reinforced Composite Materials Mold Filling Process and Mechanical Properties Analysis

An integrated simulation method for analyzing mechanical properties of injection molded fiber‐reinforced polymers

Deformation and Fracture Mechanisms of Automated Fiber Placement Pre-Preg Laminates under Out-of-plane Tensile Loading

Critical length prediction for fiber breaking in injection molded of long-fiber reinforced thin-walled products

Assessment of fiber orientation models predictability by comparison with X-ray μCT data in injection-molded short glass fiber-reinforced polyamide

Study on Rheological Properties of In-Mold Co-Injection Self-Reinforced Polymer Melt

Structure and Properties of Thin-Wall Injection Molding Long Glass Fiber Reinforced Polypropylene

Effects of Heating and Cooling of Injection Mold Cavity Surface and Melt Flow Control on Properties of Carbon Fiber Reinforced Semi-Aromatic Polyamide Molded Products

Impact Energy Dissipation and Quantitative Models of Injection Molded Short Fiber-Reinforced Thermoplastics

Investigation of fiber waviness in fused deposition modeling printed continuous fiber-reinforced polymers

Fiber Orientation in Melt Confluent Process for Reinforced Injection Molded Part

Elastic Properties of Injection Molded Short Glass Fiber Reinforced Thermoplastic Composites

Molecular Dynamics Simulation on the Interfacial Behavior of Over-Molded Hybrid Fiber Reinforced Thermoplastic Composites

Influence of Matrix Polymer on Deformation and Morphology of Injection Molded Immiscible Blends with High Interfacial Contact

An Approach for Predicting Fiber Orientation Distribution in Plastic Injection Molding of Composites

EFFECTS OF FIBER LENGTH AND ORIENTATION DISTRIBUTIONS ON THE MECHANICAL PROPERTIES OF SHORT-FIBER-REINFORCED POLYMERS

Improving the Accuracy of the Evaluation Method for the Interfacial Shear Strength of Fiber-Reinforced Thermoplastic Polymers through the Short Beam Shear Test

Research on the quality of long glass fiber‐reinforced polypropylene pipes formed via fluid‐assisted co‐injection molding

Evaluation of Local Plastic Damage in Short Fiber Dispersed Composite