Abstract:The FF losses caused by non‐radiative recombination and insufficient carrier transport are quantitatively analyzed based on the Li and Ag‐doped CZTSSe devices. The Li and Ag co‐doping strategy enables a 14.91% efficient kesterite solar cell with the highest reported FF to date of 74.30% through collaborative optimization of carrier extraction and suppression of non‐radiative recombination. In addition to open‐circuit voltage (VOC) loss, fill factor (FF) loss is considered another major factor restricting the further optimization of Cu2ZnSn(S,Se)4 (CZTSSe) device efficiency. In this work, a comprehensive investigation into the loss mechanisms of FF has been conducted, and implemented a Li&Ag co‐doping approach to enhance FF. The results indicate that the FF loss caused by insufficient carrier extraction is higher than that caused by non‐radiative recombination. The carrier extraction capability is significantly influenced by the band alignment of the CdS/CZTSSe interface and has little relationship with the carrier concentration of the absorber. Therefore, although Ag doping reduces the hole concentration and conductivity, it reduces the FF loss caused by carrier extraction due to the improvement of band alignment. Ag doping is also superior to Li in passivating harmful defects, which helps reduce FF losses caused by non‐radiative recombination. Correspondingly, Li performs better than Ag in increasing the hole carrier concentration and optimizing band alignment, greatly reducing FF losses caused by insufficient carrier transport. Finally, the Li and Ag co‐doping strategy enables a 14.91% efficient kesterite solar cell with the highest reported FF to date of 74.30% through collaborative optimization of carrier extraction and suppression of non‐radiative recombination.

Metastable defects decrease the fill factor of solar cells

Formation of Alloyed Cu2Cox Zn1-x Sn(S,Se)4 Absorption Layer and Its Application in Solar Cells

Solar cell efficiency, diode factor and interface recombination: insights from photoluminescence

Multinary Alloying Suppresses Defect Formation in Emerging Inorganic Solar Cells

Li, Ag Co‐Doping Enables Efficient Kesterite Solar Cell with a High Fill Factor of 74.30%

Ag‐Dependent Behaviour Threshold and Meta‐Stability in Wide‐Gap (Ag,Cu)(In,Ga)Se2 Solar Cells

Impact of Cation Substitution in (Ag x Cu 1− x ) 2 ZnSnSe 4 Absorber‐Based Solar Cells toward 10% Efficiency: Experimental and Theoretical Analyses

Origin of Reduced Efficiency in Cu(In,Ga)Se Solar Cells With High Ga Concentration: Alloy Solubility Versus Intrinsic Defects

Enhanced Sb2Se3 Solar Cell Performance Through Theory-Guided Defect Control

Toward High Efficient Cu2 ZnSn(Sx ,Se1- x )4 Solar Cells: Break the Limitations of VOC and FF

Composition variations in Cu(In,Ga)(S,Se)2 solar cells: not a gradient, but an interlaced network of two phases

Defect Physics in Intermediate-Band Materials: Insights from an Optimized Hybrid Functional

Improved sequentially processed Cu(In,Ga)(S,Se)2 by Ag alloying

Antisite traps and metastable defects in Cu(In,Ga)Se2 thin-film solar cells studied by screened-exchange hybrid density functional theory

Defect Engineering in Earth‐Abundant Cu2ZnSn(S,Se)4 Photovoltaic Materials Via Ga3+‐Doping for over 12% Efficient Solar Cells

Suppressing Element Inhomogeneity Enables 14.9% Efficiency CZTSSe Solar Cells

Deep defects limiting the conversion efficiency in Sb2Se3 thin-film solar cells

Efficient Cu2ZnSn(Se,S)4 solar cells with 79% fill factor using two-step annealing

Preserving the stoichiometry

Engineering Solar Cell Absorbers by Exploring the Band Alignment and Defect Disparity: The Case of Cu‐ and Ag‐Based Kesterite Compounds