Abstract:Purpose: The aim of this study is to develop a test bench, which integrates different complexity levels and enables in that way a flexible and dynamic testing for mid and long term intervals as well as testing of maximum loads till implant failure of different osteosynthesis systems on the mandible. Material and Methods: For this purpose, an analysis of the state of the art regarding existing test benches was combined with interviews of clinical experts to acquire a list of requirements. Based on these requirements a design for a modular test bench was developed. During the implementation of the test stand, functional tests were continuously carried out and improvements made. Depending on the level of complexity, the test bench can be used either as an incorporated variant or as a standalone solution. In order to verify the performance and the degree of fulfilment of the requirements of these two variants of the test bench, preliminary studies were carried out for all levels of complexity. In these preliminary studies, commercially available osteosynthesis and reconstruction plates were investigated for their biomechanical behaviour and compared with data from the literature. Results: In total, fourteen test runs were performed for the different levels of complexity. Firstly, five test runs were executed to test the simplified load scenario in the incorporated variant of the test bench. High forces could be transmitted without failure of the miniplates. Secondly a quasi-static test scenario was examined using the incorporated variant with simplified load insertion. Five experiments with a number of cycles between 40,896 and 100,000 cycles were carried out. In one case the quasi-static testing resulted in a fracture of the tested reconstruction plate with a failure mode similar to the clinical observations of failure. The last four test runs were carried out using the standalone variant of the test bench simulating complex load patterns via the insertion of forces through imitated muscles. During the test runs joint forces were measured and the amplitude and vector of the resulting joint forces were calculated for both temporomandibular joints. Differences in the force transmission depending on the implant system in comparison to the zero sample could be observed. Conclusion: The presented modular test bench showed to be applicable for examination of the biomechanical behavior of the mandible. It is characterized by the adjustability of the complexity regarding the load patterns and enables the subsequent integration of further sensor technologies. Follow-up studies are necessary to further qualify and optimize the test bench.

Approach to standardized material characterization of the human lumbopelvic system – Testing and evaluation

Soft tissue material properties based on human abdominal in vivo macro-indenter measurements

Critical evaluation of known bone material properties to realize anisotropic FE-simulation of the proximal femur

[Development and validating of a three-dimensional finite element model of total human pelvis].

Construction of Biological Model of Human Lumbar and Analysis of Its Mechanical Properties.

Comprehensively Characterizing Heterogeneous and Transversely Isotropic Properties of Femur Cortical Bones

Biomechanical research on the statically determinate pelvis under vertical loading

Biomechanical Studies of Normal Pelvis in Static Standing Position

Population-specific femur models: A step towards improved osteosynthetic biomechanical testing in orthopaedics

Measuring the global mechanical properties of the human thorax: Costo-vertebral articulation

Determination of E-modulus of cancellous bone derived from human humeri and validation of plotted single trabeculae: Development of a standardized humerus bone model

Development of a test bench for biomechanical simulation—a preliminary study of mandibular forces

An Integrated Method of Biomechanics Modeling for Pelvic Bone and Surrounding Soft Tissues.

Development of a biofidelic computational model of human pelvis for predicting biomechanical responses and pelvic fractures

Mechanical Characterization of Human Fascia Lata: Uniaxial Tensile Tests from Fresh-Frozen Cadaver Samples and Constitutive Modelling

In Vivo Assessment of Material Properties of Muscles and Connective Tissues Around the Knee Joint Based on Shear Wave Elastography.

A two-layer elasto-visco-plastic rheological model for the material parameter identification of bone tissue

[Construction and Analysis of a Finite Element Model of Human L4-5 Lumbar Segment].

The impact of the parameters of the constitutive model on the distribution of strain in the femoral head

Mechanical response of human thoracic spine ligaments under quasi-static loading: An experimental study

The effect of boundary condition on the biomechanics of a human pelvic joint under an axial compressive load: a three-dimensional finite element model