Steam reforming of methane over ordered mesoporous Ni-Mg-Al oxides

Weihua Shen,Kenta Komatsubara,Tomaya Hagiyama,Akihiro Yoshida,Shuichi Naito

DOI: https://doi.org/10.1039/b910071g

2009-11-14

Abstract:The excellent roles of mesopores were revealed clearly in preventing Ni metal from sintering as well as in preventing inactive coke accumulation under severe reaction conditions of methane steam reforming over ordered mesoporous Ni-Mg-Al oxide catalysts.

What problem does this paper attempt to address?

Steam Reforming of Methane over Ni Catalysts Prepared from Hydrotalcite-Type Precursors: Catalytic Activity and Reaction Kinetics

Yang Qi,Zhenmin Cheng,Zhiming Zhou

DOI: https://doi.org/10.1016/j.cjche.2013.11.002

2015-01-01

Abstract:Ni/Mg–Al catalysts derived from hydrotalcite-type precursors were prepared by a co-precipitation technique and applied to steam reforming of methane. By comparison with Ni/γ-Al2O3 and Ni/α-Al2O3 catalysts prepared by incipient wetness impregnation, the Ni/Mg–Al catalyst presented much higher activity as a result of higher specific surface area and better Ni dispersion. The Ni/Mg–Al catalyst with a Ni/Mg/Al molar ratio of 0.5:2.5:1 exhibited the highest activity for steam methane reforming and was selected for kinetic investigation. With external and internal diffusion limitations eliminated, kinetic experiments were carried out at atmospheric pressure and over a temperature range of 823–973K. The results demonstrated that the overall conversion of CH4 and the conversion of CH4 to CO2 were strongly influenced by reaction temperature, residence time of reactants as well as molar ratio of steam to methane. A classical Langmuir–Hinshelwood kinetic model proposed by Xu and Froment (1989) fitted the experimental data with excellent agreement. The estimated adsorption parameters were consistent thermodynamically.
Catalytic performance of Ni catalysts for steam reforming of methane at high space velocity

Xuli Zhai,Shi Ding,Zhihong Liu,Yong Jin,Yi Cheng

DOI: https://doi.org/10.1016/j.ijhydene.2010.10.053

IF: 7.2

2011-01-01

International Journal of Hydrogen Energy

Abstract:Three Ni-based catalysts, namely Ni/ZrO2/Al2O3, Ni/La–Ca/Al2O3 and Ni0.5Mg2.5AlO9 catalysts were prepared, tested and characterized for steam reforming of methane (SRM), especially at high space velocities. Experimental results demonstrated that Ni0.5Mg2.5AlO9 catalysts showed excellent catalytic activity, e.g., the high reaction performance (i.e., activity and stability) at a very short residence time of 20ms. For the accompanied water gas shift (WGS) reaction with the SRM at the steam to methane ratio of 3:1, the overall hydrogen yield depended on both the CH4 conversion and the CO2 selectivity. The results showed that CO2 selectivity had opposite trend compared with CH4 conversion in such a short-contact process. Catalyst characterizations by XRD, SEM-EDS, TEM and TGA suggested that the good performance of nickel catalysts was closely related with the good dispersion of the active component. The nano-sized nickel particles in strong interaction with the supports would lead to the good dispersion, thereafter having a slight tendency to sintering, and then to coking.
Meso-porous Ni/Mg/Al catalysts for methane reforming with CO2

Zhaoyin Hou,Tatsuaki Yashima

DOI: https://doi.org/10.1016/j.apcata.2003.11.002

2004-01-01

Abstract:A series of Ni/Mg/Al catalysts were prepared by coprecipitation method and used in methane reforming with CO2. It was found that these catalysts possessed a meso-porous structure and wide surface area. X-ray diffraction (XRD) analysis indicated that Ni existed mainly in NiAl2O4 and/or Ni-Mg-O solid solution in Ni/Mg/Al. The higher surface area of the catalysts allowed the stronger interaction between Ni and Al-Mg, which improved the dispersion of Ni, and retarded the sintering of Ni during the reforming process. And then the highly dispersed Ni increased the adsorption of CO2, exhibiting a higher reforming activity, lower coke formation and a higher stability. The activation processes of CO2 and CH4 on Ni/Mg/Al catalysts were investigated by CO2 temperature-programmed desorption (CO2-TPD) and coke reaction via CH4 temperature-programmed decomposition.
Carbon Dioxide Reforming of Methane over Ordered Mesoporous NiO–MgO–Al2O3 Composite Oxides

Leilei Xu,Huanling Song,Lingjun Chou

DOI: https://doi.org/10.1016/j.apcatb.2011.08.028

IF: 6.177

2011-01-01

Catalysis Science & Technology

Abstract:Ordered mesoporous NiO–MgO–Al2O3 composite oxides with various Ni and Mg content were facilely synthesized via one pot evaporation induced self-assembly (EISA) strategy. These mesoporous materials with large specific surface areas, big pore volumes, uniform pore sizes and superior thermal stability were investigated as the catalysts for the carbon dioxide reforming of methane reaction. These materials performed high catalytic activity as well as long stability. The improved catalytic performances were suggested to be closely associated with both the amount of “accessible” active centers for the reactants owing to their advantageous structural properties and the stabilized Ni nanoparticles by mesoporous framework matrix due to the “confinement effect” of the mesopores. Besides, the role of the MgO basic modifier was also studied. It was observed that only moderate amount of the Mg containing (2M%) could greatly promote the catalytic performances. The stabilized Ni nanoparticles as well as doped MgO had reinforced capacity of resistance to coke, accounting for no deactivation after 100h long-term stability test at 700°C. Therefore, the ordered mesoporous NiO–MgO–Al2O3 composite oxides promised a series of novel and stable catalyst candidates for carbon dioxide reforming of methane reaction.
A Plate-Type Anodic Alumina Supported Nickel Catalyst for Methane Steam Reforming

Lu Zhou,Yu Guo,Qi Zhang,Thanh Phong Tran,Makoto Sakurai,Hideo Kameyama

DOI: https://doi.org/10.1252/jcej.07we182

2008-01-01

JOURNAL OF CHEMICAL ENGINEERING OF JAPAN

Abstract:An anodic alumina supported nickel catalyst (Ni/Al2O3/Alloy) was synthesized using a double impregnation method with a high temperature calcination in between, to investigate reactivity performance thereof during steam reforming of methane (SRM) reactions in continuous and daily start-up and shutdown (DSS)-like operations. The catalyst was structurally characterized using X-ray diffraction (XRD), BET and temperature programmed reduction (TPR) technologies. The TPR results showed that almost all nickel content from the first impregnation was transformed into nickel aluminate, whereas nickel from the second impregnation predominantly existed in the more reducible forms of NiO and xNiO center dot Al2O3 (x < 1). The existence of these NiO and NiAl2O4 phases was identified by XRD. The catalyst provided high and stable SRM reactivity near the equilibrium value, while no deactivation was observed in continuous durability testing for 200 h at 800 degrees C and 130 h at 700 degrees C, and in DSS-like mode operation at 700 degrees C. The investigation of the influence of methane and/or steam treatments on the reactivity of Ni/Al2O3/Alloy showed the catalyst is not disturbed by the methane treatment, whereas it is remarkably deactivated by the steam treatment. In addition, no differences in the reduction effect were found when using hydrogen or methane to regenerate a steamed catalyst.
Carbon Dioxide Reforming of Methane over Cobalt‐Nickel Bimetal‐Doped Ordered Mesoporous Alumina Catalysts with Advanced Catalytic Performances

Leilei Xu,Fagen Wang,Mindong Chen,Jian Zhang,Kaidi Yuan,Liangjun Wang,Kai Wu,Guoqin Xu,Wei Chen

DOI: https://doi.org/10.1002/cctc.201600472

IF: 4.5

2016-01-01

ChemCatChem

Abstract:Co‐Ni bimetal‐doped ordered mesoporous Al2O3 composite oxides with different Co/(Co+Ni) ratios were designed and fabricated by a one‐pot evaporation‐induced self‐assembly method. The obtained materials, which had an ordered mesostructure and outstanding thermal stability, were investigated as catalysts for the CO2 reforming of CH4. The effects of the Co/(Co+Ni) molar ratios and ordered mesostructure on the catalytic performances were investigated systematically. The ordered mesoporous Co‐Ni bimetallic catalysts exhibited both higher catalytic activities and better anticoke properties than the corresponding monometallic materials because of the Co‐Ni synergistic effect. Furthermore, the ordered mesostructure could promote the catalytic performances significantly by providing gaseous reactants with enough accessible metallic active centers and stabilizing the metallic nanoparticles through the confinement effect of the mesoporous framework. As a result, these mesoporous Co‐Ni bimetallic catalysts had more enhanced catalytic properties and anticoke ability than traditional supported catalysts toward the CO2 reforming of CH4, which promises a series of potential catalyst candidates.
Highly active and stable Ni/perovskite catalysts in steam methane reforming for hydrogen production

Zhiliang Ou,Zhonghui Zhang,Changlei Qin,Hongqiang Xia,Tao Deng,Juntian Niu,Jingyu Ran,Chunfei Wu

DOI: https://doi.org/10.1039/d1se00082a

2021-01-01

Abstract:The roles of A and B sites in a perovskite support in the catalytic performance of Ni-based catalysts were revealed for steam methane reforming and the Ni/La 0.7 Mg 0.3 AlO 3−δ catalyst has an outstanding catalytic activity and resistance to carbon deposition.

materials science, multidisciplinary,chemistry, physical,energy & fuels
Ordered Mesoporous Alumina Supported Nickel Based Catalysts for Carbon Dioxide Reforming of Methane

Leilei Xu,Huahua Zhao,Huanling Song,Lingjun Chou

DOI: https://doi.org/10.1016/j.ijhydene.2012.01.105

IF: 7.2

2012-01-01

International Journal of Hydrogen Energy

Abstract:Ordered mesoporous alumina facilely synthesized via improved evaporation-induced self-assembly (EISA) strategy was provided with large specific surface area, big pore volume, uniform pore size and excellent thermal stability. The obtained mesoporous material was used as the carrier of the Ni based catalysts for carbon dioxide reforming of methane. These mesoporous catalysts performed high catalytic activity and long stability. Typically, the catalytic conversions of the CH4 and CO2 were greatly close to the equilibrium conversion and no deactivation was observed during the 100 h long lifetime test. The advantageous structural properties of ordered mesoporous alumina contributed to high dispersion of the Ni particles among the mesoporous framework, which further accounted for the good catalytic activity due to more "accessible" Ni active sites for the reactants. The "confinement effect" of the mesopores could effectively prevent the thermal sintering of the Ni nanoparticles to some extent, committed to its long-term catalytic stability. Besides, the mesoporous catalysts possessed enhanced ability to withstand coke, although not any modifiers had been added. Properties of the coke over the mesoporous catalyst were also carefully investigated. Therefore, the ordered mesoporous alumina was a promising catalyst support for the carbon dioxide reforming with methane. Copyright (C) 2012, Hydrogen Energy Publications, LLC. Published by Elsevier Ltd. All rights reserved.
STUDIES ON STEAM REFORMING OF METHANE OVER Ni/ZrO2 CATALYST

胡捷,贺德华,李映伟,张昕,王晖

DOI: https://doi.org/10.3969/j.issn.0253-2409.2004.01.020

2004-01-01

Journal of Fuel Chemistry and Technology

Abstract:The catalytic performances of Ni/ZrO2 in the steam reforming of methane were studied. Ni/ZrO2 catalyst had relatively high activity and stability in the steam reforming of methane. No significant influence was observed on the catalytic activity when the calcinations temperatures of the support changed from 550° to 850°C. The catalyst reduced at 550°C showed higher activity, but a little influence on the CO selectivity in the range of reduction temperature from 450° to 750°C. The conversion of methane increased with the increase of H2O/CH4 ratio, while CO selectivity decreased. The conversion of methane and CO selectivity decreased with the increase of space velocity. The result of 85% methane conversion and 70% CO selectivity was obtained over 10% Ni/ZrO2, catalyst under the condition of 650°C, 1.984 × 104/hr and H2O/CH4/N2 = 2:1:2.67.
Reforming of methane and coalbed methane over nanocomposite Ni/ZrO2 catalyst

Qinhui Zhang,Yan Li,Bin Xu

DOI: https://doi.org/10.1016/j.cattod.2004.09.015

IF: 5.3

2004-01-01

Catalysis Today

Abstract:Nanocomposite Ni/ZrO2-AN catalyst consisting of comparably sized Ni metal and ZrO2 nanoparticles is studied in comparison with zirconia- and alumina-supported Ni catalysts (Ni/ZrO2-CP and commercial Ni/Al2O3-C) for steam reforming of methane (SRM) and for combined steam and CO2 reforming of methane (CSCRM). The reactions are performed under atmospheric pressure with stoichiometric amounts of H2O and CH4 or (H2O + CO2) and CH4 at 1073 K. Under a wide range of methane space velocity (gas hourly space velocity of methane GHSVCH4 = 12,000–96,000 ml/(h gcat.), the nanocomposite Ni/ZrO2-AN catalyst always shows higher activity and stability for both SRM and CSCRM reactions. The two supported Ni catalysts (Ni/ZrO2-CP and Ni/Al2O3-C) exhibit fairly stable catalysis under low GHSVCH4 but they are easily deactivated under high GHSVCH4 and become completely inactive when they are reacted for ca.100 h at GHSVCH4 = 48,000 ml/(h gcat.). The CSCRM reaction is carried out with different H2O/CO2 ratios in the reaction feed while keeping the molar ratio (H2O + CO2)/CH4 = 1.0, the results prove that the nanocomposite Ni/ZrO2-AN catalyst can be highly promising in enabling a catalytic technology for the production of syngas with flexible H2/CO ratios (ca. H2/CO = 1.0–3.0) to meet the requirements of various downstream chemical syntheses.
Steam Reforming of Methane over Nickel-Aluminum Spinel-Derived Catalyst

Xi Ding,Bing Li,Yunfeng Yang,Xiaohui Liu,Yong Guo,Yanqin Wang

DOI: https://doi.org/10.1016/j.ijhydene.2023.09.167

IF: 7.2

2024-01-01

International Journal of Hydrogen Energy

Abstract:Despite steam reforming of methane (SRM) has been the dominant way to produce hydrogen in industrial owing to its large hydrogen production capacity, easy accessibility of feedstocks and relative low cost, the development of high-efficient catalysts is still of great significance. In this work, we report the synthesis, characterizations and evaluation of Nickel-aluminum spinel (NiAl2O4) catalyst in SRM reaction. Compared with Ni/g-Al2O3 catalyst prepared by impregnation, NiAl2O4 presents higher methane conversion. Virous of characterizations exhibit NiAl2O4 possesses higher distribution of Ni and smaller Ni nanoparticle size, which is one of advantages for its high activity. Another vital reason is the generation of oxygen vacancies in spinel during the reduction, which is beneficial for the activation of water. Moreover, NiAl2O4 catalyst shows extremely stability without obvious deactivation in 160 h. This study illustrates that the construction of catalyst with high activity and stability via NiAl2O4 spinel and reals its high activity origination. (c) 2023 Hydrogen Energy Publications LLC. Published by Elsevier Ltd. All rights reserved.
The performances of Ni–MgO@γ-Al2O3 for steam methane reforming prepared by freeze-drying technology

Yanhui Li,Shengwu Huang,Bingwen Lu,Zhaoyang Deng,Dongdong Dong,Xinyue Zhang,Shanghua Wu,Xin Deng

DOI: https://doi.org/10.1016/j.ijhydene.2024.02.049

IF: 7.2

2024-03-01

International Journal of Hydrogen Energy

Abstract:Ni-based catalysts are an indispensable part for methane reforming, but the catalyst deactivation occurs at high reforming temperatures due to coke deposition and sintering. In this work, co-impregnation and freeze drying method was developed to prepare the Ni-based catalyst which were characterized by XRD, TEM and H2-TPR. And the effects of freeze drying method and MgO on CH4 conversion, H2 yield and CO selectivity were investigated. The results revealed that the application of the freeze-drying method promoted the dispersion of Ni particles on the surface of γ-Al2O3 support. Moreover, the inclusion of MgO further enhanced Ni dispersion and suppressed the particle size of the catalysts. Among the prepared catalysts, the 0.05MgO–Ni/γ-Al2O3 catalyst showed the best catalytic performance. CH4 conversion, H2 yield and CO selectivity respectively exceeded 75%, 55% and 90% under the conditions of an S/C ratio of 2 and reforming temperature of 600 °C after 10 h.

energy & fuels,electrochemistry,chemistry, physical
Reforming Of Methane And Coalbed Methane Over Nanocomposite Nni/Zro2.

Qh Zhang,Bq Xu,Y Li

DOI: https://doi.org/10.1016/j.cattod.2004.09.015

IF: 5.3

2004-01-01

Catalysis Today

Abstract:Nanocomposite Ni/ZrO2-AN catalyst consisting of comparably sized Ni metal and ZrO2 nanoparticles is studied in comparison with zirconia- and alumina-supported Ni catalysts (Ni/ZrO2-CP and commercial Ni/Al2O3-C) for steam reforming of methane (SRM) and for combined steam and CO2 reforming of methane (CSCRM). The reactions are performed under atmospheric pressure with stoichiometric amounts of H2O and CH4 or (H2O+CO2) and CH4 at 1073K. Under a wide range of methane space velocity (gas hourly space velocity of methane GHSVCH4=12,000–96,000ml/(hgcat.), the nanocomposite Ni/ZrO2-AN catalyst always shows higher activity and stability for both SRM and CSCRM reactions. The two supported Ni catalysts (Ni/ZrO2-CP and Ni/Al2O3-C) exhibit fairly stable catalysis under low GHSVCH4 but they are easily deactivated under high GHSVCH4 and become completely inactive when they are reacted for ca.100h at GHSVCH4=48,000ml/(hgcat.). The CSCRM reaction is carried out with different H2O/CO2 ratios in the reaction feed while keeping the molar ratio (H2O+CO2)/CH4=1.0, the results prove that the nanocomposite Ni/ZrO2-AN catalyst can be highly promising in enabling a catalytic technology for the production of syngas with flexible H2/CO ratios (ca. H2/CO=1.0–3.0) to meet the requirements of various downstream chemical syntheses.
Bi-reforming of Methane with Steam and CO2 under Pressurized Conditions on a Durable Ir-Ni/MgAl2O4 Catalyst.

Zhongxian Liu,Feifan Gao,Yi-An Zhu,Zhicheng Liu,Kake Zhu,Xinggui Zhou

DOI: https://doi.org/10.1039/d0cc05874b

IF: 4.9

2020-01-01

Chemical Communications

Abstract:High pressure reforming of methane is critical for process economics, but imposes increased risk of catalyst coke deposition. Herein, a coke- and sintering-resistant Ir-Ni alloy catalyst is presented, which is durable in methane bi-reforming at 850 °C and 20 bars for up to 434 h.
A novel catalyst with plate-type anodic alumina supports, Ni/NiAl2O4/γ-Al2O3/alloy, for steam reforming of methane

Lu Zhou,Yu Guo,Qi Zhang,Masayuki Yagi,Jun Hatakeyama,Huabo Li,Jian Chen,Makoto Sakurai,Hideo Kameyama

DOI: https://doi.org/10.1016/j.apcata.2008.06.007

2008-01-01

Abstract:A 17.9wt% plate-type metal-monolithic anodic alumina supported Ni catalyst with an interfacial NiAl2O4 layer showed excellent SRM reactivity at 700°C and this was believed to be resulted from the existence of interfacial NiAl2O4 layer which anchored the top metallic nickel particles and effectively suppressed catalyst sintering.
Methane reforming to synthesis gas over Ni catalysts modified with noble metals

Dalin Li,Yoshinao Nakagawa,Keiichi Tomishige

DOI: https://doi.org/10.1016/j.apcata.2011.09.018

2011-11-01

Abstract:Nickel is an effective component for the steam reforming of methane in terms of the catalytic activity and the catalyst cost. When Ni catalysts are applied to dry reforming, oxidative reforming, and catalytic partial oxidation, it is necessary to add the properties of high resistance to oxidation, hot spot formation, and coke deposition, to the Ni catalysts. An efficient method for giving these properties while considering the catalyst cost is the modification of Ni metal particles with small amounts of noble metals. An important point is that preparation methods can affect the structure of noble metal–Ni bimetallic particles, which is connected to the catalytic performances. The additive effects of noble metals on the catalytic performances are summarized in terms of activity, suppression of Ni oxidation, carbon formation, self-activation, and sustainability in the daily startup and shutdown operations.
New Mechanism Insights into Methane Steam Reforming on Pt/Ni from DFT and Experimental Kinetic Study

Juntian Niu,Yalan Wang,Yanying Qi,Anh H. Dam,Hongmin Wang,Yi-An Zhu,Anders Holmen,Jingyu Ran,De Chen

DOI: https://doi.org/10.1016/j.fuel.2020.117143

IF: 7.4

2020-01-01

Fuel

Abstract:In this contribution, we combine density functional theory (DFT) calculations, experimental kinetic study and DFT-assisted analysis to elucidate the impact of the interface of monolayer Pt on the Ni surface on catalytic performance of steam methane reforming including carbon formation on core-shell (Ni@Pt) catalysts and compare it with Ni and Pt catalysts. We demonstrate that core-shell structured Ni@Pt significantly lowers the carbon formation without sacrificing much the activity. The DFT results demonstrate that the metal identity, core shell structure and support have significant impacts on the reaction mechanisms. The direct methane activation is energetically favorable reaction pathway on Ni, while the OH* assisted methane activation is the favorable pathway on Pt and Ni@Pt catalysts, where methane activation is the rate-determining step on all catalysts. We unambiguously reveal that the core-shell Ni@Pt catalyst modified the surface Pt electron density and shifted d-band center away from Fermi level compared to Ni(1 1 1) and Pt(1 1 1). It results in a strong basic surface OH* which actively reacts with CHx and thus enhances carbon formation resistance. Above all, Ni-core/Pt-shell particle could decouple the activity and carbon resistance to keep the activity and reduce carbon formation simultaneously in methane steam reforming. In addition, by taking into account the activation of steam on the support, the effective activation energy estimated from DFT-assisted analysis is well consistent with the experimental value on the both Ni and Ni@Pt catalysts, which could shed some light on building a bridge between experimental work and DFT-assisted kinetic study.
Progresses in the Preparation of Coke Resistant Ni‐based Catalyst for Steam and CO2 Reforming of Methane

changjun liu,jingyun ye,jiaojun jiang,yunxiang pan

DOI: https://doi.org/10.1002/cctc.201000358

IF: 4.5

2011-01-01

ChemCatChem

Abstract:Steam reforming of methane is an extremely important process for the hydrogen and syngas production. Nickel-based catalysts have been extensively employed in the industrial process of steam reforming because of their high activity, low cost, and the plentiful supply of Nickel. Nickel-based catalysts have also shown high activity for CO2 reforming of methane, which has been considered as a good option, with consumption of a significant amount of carbon dioxide. However, a major challenge is that Ni catalysts have a high thermodynamic potential for coke formation during reforming reactions. For steam reforming, coke formation induces deactivation of the catalyst, especially if the carbon forms as carbon filaments. The filamentous carbon material has a high mechanical strength and can cause mechanical deformation of the catalyst. For CO2 reforming, coke formation over Ni catalyst is even more serious and leads to rapid deactivation of the catalyst. It is highly desired to design and synthesize a coke resistant Ni catalyst not only for reforming of methane, but also for reforming of other hydrocarbons (including biomass derived hydrocarbons). Herein we summarize the very recent progresses in the design, synthesis, and characterization of coke resistant Ni catalysts for steam and CO2 reforming of methane. The progresses in the use of promoters, in the effect of supporting materials and in the preparation methods have been discussed. The thermal stability, regeneration, and future development of coke resistant Ni catalysts for these processes are also briefly addressed.
Bi-reforming of Methane with Carbon Dioxide and Steam on Nickel-Supported Binary Mg–Al Metal Oxide Catalysts

Dedong He,Yimin Zhang,Zichun Wang,Yi Mei,Yijiao Jiang

DOI: https://doi.org/10.1021/acs.energyfuels.9b03312

2020-03-13

Abstract:Bi-reforming of methane (CH4) with carbon dioxide (CO2) and steam is a promising process to produce syngas with a H2/CO ratio of about 2, which can be directly used as a feedstock for methanol synthesis. This work studied nickel nanoparticles supported on the binary Mg–Al metal oxide catalysts for the bireforming of CH4. The XRD, TEM, and FT-IR results confirm the successful synthesis of Ni/MgO, Ni/MgxAlyO, and Ni/Al2O3 catalysts. The TPR profile shows that the reduction temperature of Ni species was slightly decreased upon addition of Al due to the formation of the NiAl2O4 phase. The XPS spectra demonstrate that Ni/MgO and Ni/Al2O3 exhibit higher amounts of Ni0 after H2 reduction. It can explain the origin of the superior catalytic performance of Ni/MgO and Ni/Al2O3 over the Ni/MgxAlyO catalysts possessing less Ni0 species during the H2 reduction process. Compared to the conventional dry reforming of CH4, the bi-reforming process features a higher CH4 conversion and a H2/CO ratio close to 2, which is suitable for methanol synthesis without further separation and adjustment steps.

energy & fuels,engineering, chemical
Balancing Ni0 and Ni2+ on Γ‐al2o3 for Efficient Steam Methane Reforming

Junjie Zhang,Zhourong Xiao,Li Wang,Xiangwen Zhang,Guozhu Li

DOI: https://doi.org/10.1002/slct.202203339

2022-01-01

ChemistrySelect

Abstract:Steam methane reforming (SMR) is the most mature technology for hydrogen production in industry, and alumina supported nickel (Ni/Al2O3) is the most widely used catalyst. Herein, the key role of Ni valence state on the catalytic SMR performance of Ni/Al2O3 is reported. The ratio of Ni-0/Ni2+ on Ni/Al2O3 is individually and effectively tuned by changing the reduction temperature after wet impregnation. Catalytic performance of Ni/Al2O3 is greatly dependent on the surface concentration of Ni-0 and Ni2+. The catalyst reduced at 675 degrees C possesses balanced Ni-0 and Ni2+ sites and exhibits superior catalytic performance, on which 60 % of methane is stably converted at 600 degrees C. CH4-TPD and CO-TPD profiles demonstrate that appropriate Ni-0/Ni2+ ratio can promote the adsorption of CH4 and inhibit the moderate-strength adsorption of CO, which leads to increased SMR activity and selectivity.

Steam reforming of methane over ordered mesoporous Ni-Mg-Al oxides

Steam Reforming of Methane over Ni Catalysts Prepared from Hydrotalcite-Type Precursors: Catalytic Activity and Reaction Kinetics

Catalytic performance of Ni catalysts for steam reforming of methane at high space velocity

Meso-porous Ni/Mg/Al catalysts for methane reforming with CO2

Carbon Dioxide Reforming of Methane over Ordered Mesoporous NiO–MgO–Al2O3 Composite Oxides

A Plate-Type Anodic Alumina Supported Nickel Catalyst for Methane Steam Reforming

Carbon Dioxide Reforming of Methane over Cobalt‐Nickel Bimetal‐Doped Ordered Mesoporous Alumina Catalysts with Advanced Catalytic Performances

Highly active and stable Ni/perovskite catalysts in steam methane reforming for hydrogen production

Ordered Mesoporous Alumina Supported Nickel Based Catalysts for Carbon Dioxide Reforming of Methane

STUDIES ON STEAM REFORMING OF METHANE OVER Ni/ZrO2 CATALYST

Reforming of methane and coalbed methane over nanocomposite Ni/ZrO2 catalyst

Steam Reforming of Methane over Nickel-Aluminum Spinel-Derived Catalyst

The performances of Ni–MgO@γ-Al2O3 for steam methane reforming prepared by freeze-drying technology

Reforming Of Methane And Coalbed Methane Over Nanocomposite Nni/Zro2.

Bi-reforming of Methane with Steam and CO2 under Pressurized Conditions on a Durable Ir-Ni/MgAl2O4 Catalyst.

A novel catalyst with plate-type anodic alumina supports, Ni/NiAl2O4/γ-Al2O3/alloy, for steam reforming of methane

Methane reforming to synthesis gas over Ni catalysts modified with noble metals

New Mechanism Insights into Methane Steam Reforming on Pt/Ni from DFT and Experimental Kinetic Study

Progresses in the Preparation of Coke Resistant Ni‐based Catalyst for Steam and CO2 Reforming of Methane

Bi-reforming of Methane with Carbon Dioxide and Steam on Nickel-Supported Binary Mg–Al Metal Oxide Catalysts

Balancing Ni0 and Ni2+ on Γ‐al2o3 for Efficient Steam Methane Reforming