Abstract:With the progress in modern high-energy physics, the Standard Model is constantly being refined. As the last brick of the Standard Model, the Higgs boson was confirmed to be discovered in the Large Hadron Collider (LHC) in 2012. For the further exploration of the Higgs boson, the Circular Electron Positron Collider (CEPC) is proposed. The baseline detector concept of CEPC is guided by the particle flow principle. The Particle Flow Algorithm (PFA) reconstructs a list of low-level particles and associates every detector hit with these particles. The high granularity hadronic calorimeter (HCAL) represents an essential component of PFA-based detectors. This paper mainly presents the single-layer electronics design and development for the scintillator analog hadronic calorimeter prototype (AHCAL). The single-layer readout electronics consists of front-end electronics board (FEB) and data interface (DIF) board. The FEB carries the silicon photomultipliers (SiPM), plastic scintillators, and the SiPM signal readout circuit. A single SiPM coupled with a scintillator constitute the basic detection unit. The size of scintillator used here is 4 cm x 4 cm. A sensitive area of 72 x 72 cm(2) can be covered by the design presented here. 324 SiPMs coupled with scintillators are mounted on each FEB. Besides the huge sensitive area, The AHCAL prototype must also meet strict requirements on the integration and robustness of the electronics. This paper develops a complete single-layer readout electronics design that meets the requirements for use in the AHCAL. The results of beam test shows that the peak of the minimum ionizing particle (MIP) is separated from the pedestal evidently and the signal-to-noise ratio (SNR) is better than 20. The volume required for the electronics is less than 4 cm3 per channel. In addition, the FEB is sufficiently robust to avoid damage during intercontinental transportation. The development of the single-layer electronics represents significant progress in the design of a prototype device that meets the requirement for use in the CEPC.

Development of a CsI:Tl calorimeter subsystem for the All-Sky Medium-Energy Gamma-Ray Observatory (AMEGO)

Subsystem Development for the All-Sky Medium Energy Gamma-ray Observatory (AMEGO) prototype

Development of a CsI Calorimeter for the Compton-Pair (ComPair) Balloon-Borne Gamma-Ray Telescope

Development of Dual-Gain SiPM Boards for Extending the Energy Dynamic Range

Exploring Large-Volume GAGG Scintillators for use in MeV Gamma-Ray Astrophysics

Results from the CsI Calorimeter onboard the 2023 ComPair Balloon Flight

Design of a high-dynamic-range prototype readout system for VLAST calorimeter

Development of a SiPM Pixel Prototype for the Large-Sized Telescope of the Cherenkov Telescope Array

Evaluation of the performance of a CdZnTe-based soft $γ$-ray detector for CubeSat payloads

Prototype Tests for a Highly Granular Scintillator-Based Hadronic Calorimeter

RADiCAL: Precision-timing, Ultracompact, Radiation-hard Electromagnetic Calorimetry

The Single-Layer Readout Electronics Design and Development for CEPC Scintillator Analog Hadronic Calorimeter Prototype

Development of TRL5 Space Qualified Hardware for Tuning, Biasing, and Readout of Kilopixel TES Bolometer Arrays

ORIGAMIX, a CdTe-based spectro-imager development for nuclear applications

Design and Testing of a Prototype Pixellated CZT Detector and Shield for Hard X-Ray Astronomy

Performance Evaluation of a silicon-based 6U Cubesat detector for soft $γ$-ray astronomy

Evaluation of the performance of a CdZnTe-based soft -ray detector for CubeSat payloads

Design and construction of the Mini-Calorimeter of the AGILE satellite

Development of COTS ADC SEE Test System for the ATLAS LAr Calorimeter Upgrade

Design of a Prototype Readout Electronics for a Low-energy Ion Spectrometer in Near-earth Space

On-beam system test of the new readout electronics for the CMS Electromagnetic Calorimeter upgrade