Abstract:Thermal barrier coatings (TBCs) are extensively used in gas turbine engines in power generation and aerospace applications. Improvements in TBC performance and lifetime are continuously pursued by the gas turbine industry. Suspension plasma spraying (SPS) has shown promising results in recent years as it could produce a porous columnar TBC microstructure exhibiting low thermal conductivity and high durability. Further improvements in lifetime and fundamental understanding of failure mechanisms would lead to their wider application. Lifetime of a TBC system is dependent not only on the topcoat microstructure and chemistry, but also on topcoat-bondcoat interface and bondcoat characteristics as they influence the growth rate of thermally grown oxide (TGO) layer as well as the mismatch stresses generated in the topcoat during operation. Moreover, in SPS TBCs, the column density and porosity in the topcoat are also affected by the bondcoat surface roughness which in turn affects TBC lifetime. In previous work, it was shown that bondcoat surface treatment by shot peening followed by light grit blasting can significantly enhance the cyclic lifetime of SPS TBCs. The objective of this work was to gain further insight into the lifetime improvements due to surface treatment of bondcoat. Commercial NiCoCrAlY powder was deposited by high velocity air fuel (HVAF) and high velocity oxy fuel (HVOF) spraying while SPS was used to deposit yttria stabilised zirconia topcoat. Before spraying the topcoat, the bondcoat samples were subjected to vacuum heat treatment, shot peening, and/or grit blasting. Residual stress measurements were performed by X-ray diffraction on samples with different variants of bondcoat treatments and compared with Almen strip tests. The lifetime was examined by thermal cyclic fatigue testing. The relationships between changes in bondcoat surface roughness, residual stress state and microstructure due to surface treatments, and resultant topcoat microstructure and lifetime were studied and discussed.

Improvement of the durability of thermal barrier coating by pre-oxidation

TGO stress growth for Pt-modified aluminide bond coats during high temperature oxidation

Influence factors of high temperature oxidation for Pt-modified-aluminide bond coatings

Lifetime Extension of Atmospheric and Suspension Plasma-Sprayed Thermal Barrier Coatings in Burner Rig Tests by Pre-Oxidizing the CoNiCrAlY Bond Coats

Restrained TGO Growth in YSZ/NiCrAlY Thermal Barrier Coatings by Modified Laser Remelting

Effect of Pre-Heat-Treatment on the Oxidation Resistance of MCrAlY Coatings: A Review

High‐temperature oxidation and TGO growth behavior of Sr.9(Zr.9Yb.05Y.05)O2.85 thermal barrier coatings

The Impedance Spectroscopy Study of the Oxides Layer in Thermal Barrier Coatings

Understanding the effect of bondcoat surface treatment on enhanced lifetime of suspension plasma sprayed thermal barrier coatings

TiC-self-healing thermal barrier coating structures and oxidation resistance

Improved Thermal Cycling Durability of Thermal Barrier Coatings Manufactured by PS-PVD

Effect of pre-treatment temperatures on the oxidation behaviors and surface roughening mechanisms of NiCoCrAlYHf coating

Isothermal Oxidation TGO Growth Behaviors of Laser-Remolten LZO/YSZ Thermal Barrier Coatings

Structural characteristics and high-temperature oxidation behaviour of nano-HfO2-doped thermal barrier coatings

Isothermal and Cyclic Oxidation Performance of Vertically Cracked and Columnar Thermal Barrier Coating Structures Produced Using Axial Suspension Plasma Spraying Process

Superior oxidation resistant MCrAlY bond coats prepared by controlled atmosphere heat treatment

Microstructure and thermal behaviour of plasma sprayed zirconia/alumina composite coating

Investigation on the Oxidation Behavior of the NiCrAlY Bond-Coat with Low Al Content Sprayed by High Velocity Oxygen Fuel Method

Isothermal Oxidation Behavior of VC and Columnar Structured Thermal Barrier Coatings Deposited by Suspension Plasma Spray Technology

The failure behavior of thermally grown oxide of the AlCoCrFeNi bond coating prepared by atmospheric plasma spray at 900–1000 °C

Non-destructive Evaluation of Thermally Grown Oxides in Thermal Barrier Coatings Using Impedance Spectroscopy