Abstract:The low quality of up-facing inclined surfaces, combined with a lack of in-situ treatments, is a crucial challenge in Laser Powder Bed Fusion of metals. A recently proposed strategy, so-called Incremental Dual Laser Powder Bed Fusion (IDLPBF), aims to enhance the quality of up-facing inclined surfaces of metal parts directly during building. This is achieved through automatically alternating between laser remelting and building in height steps of 1.5 mm. Laser remelting involves selectively removing powder that is covering the inclined surface through nanosecond pulsed laser-induced shock waves and subsequently remelting the uncovered surface using a continuous wave laser. Treated surfaces are hence composed of laser remolten zones separated by elevated ridges in the overlap region, referred to as stitching zones. These stitching zones can compromise the geometrical accuracy and, consequently, pose a serious risk to fatigue performance. This work focuses on the enhancement of stitching zones and resulting quality of inclined surfaces through IDLPBF of a novel tool steel (M789). The paper covers the effect of various scan strategies for laser remelting on the stitching zone size. By optimizing the orientation of consecutive remelting passes and the position of the remelting fields, the stitching zone width could be reduced from 830 μm to 70 μm. Moreover, the optimized IDLPBF process was successfully applied to a large range of surface inclinations with respect to the horizontal build plate (5°-60°). For the first time, a significant quality improvement for 60° inclined surfaces was achieved, reducing the stress concentration factor by 35 %. The significantly reduced maximum stress concentrations were largely observed at stitching zones, in contrast to multiple high stress concentration sites randomly scattered across as-built surfaces. As a proof of concept, 60 mm high demonstrator parts including typically inaccessible surfaces located in the shadow zone were fully automated manufactured by IDLPBF.

Precontouring as a Tool to Improve the Laser Powder Bed Fusion Printability of Inconel939 Thin Walls

Influence of Pre- and Post-Contouring Strategies to Downskin Sloped Surfaces in Laser Powder-Bed Fusion (L-PBF) Additive Manufacturing

Elucidating the effect of preheating temperature on melt pool morphology variation in Inconel 718 laser powder bed fusion via simulation and experiment

Investigation of Scanning Strategies and Laser Remelting Effects on Top Surface Deformation of Additively Manufactured IN 625

A Surface Quality Optimization Strategy Based on a Dedicated Melt-Pool Control Via the Dashed-Scan Contouring Technique in Electron Beam Powder Bed Fusion

Assessment of Residual Stresses in Laser Powder Bed Fusion Manufactured IN 625

The evolution of microstructure and mechanical properties of Inconel 625 alloy fabricated by laser powder bed fusion via novel hybrid scanning strategy

The effect of rescanning strategy on residual stress and deformation of laser-based powder bed fusion of 316L stainless steel thin-walled parts

Effect of scanning tracks on the contour morphology and dimensional accuracy of the fine structure manufactured by laser powder bed fusion

Study of Powder Entrainment in L-PBF Process with Maximum Hatching Space for Higher Process Efficiency

Unveiling the impact of layerwise laser preheating on microstructure and mechanical response in laser powder bed fusion

Effect of remelting on cracking of Inconel 939 fabricated via laser powder bed fusion

Experimental Quantification of Inward Marangoni Convection and Its Impact on Keyhole Threshold in Laser Powder Bed Fusion of Stainless Steel

Tailored microstructure by using in-situ re-scanning and its influence on fatigue crack growth behavior of Inconel 718 fabricated by LPBF at elevated temperature

Effect of laser focal point position on porosity and melt pool geometry in laser powder bed fusion additive manufacturing

Novel strategy for automated quality enhancement of up-facing inclined surfaces by incremental dual laser powder bed fusion

Tailoring Microstructure and Mechanical Properties of Additively Manufactured Inconel 625 by Remelting Strategy in Laser Powder Bed Fusion

Application of in situ process monitoring to optimise laser parameters during laser powder bed fusion printing of Ti-6Al-4V parts with overhang structures

In Situ Microstructure Modification Using a Layerwise Surface-Preheating Laser Scan of Ti-6Al-4V during Laser Powder Bed Fusion

Laser Powder Bed Fusion Process Parameters' Optimization for Fabrication of Dense IN 625

A66Pathways to exploit the multi-spot scanning strategy in electron beam additive manufacturing for control of microstructure and defect density