Abstract:The most common primary damage form of rubber asphalt pavements is fatigue cracking. At present, the indirect tension, direct tension, bending, and unconfined compression tests are the main considered fatigue parameters to design the structure of rubber asphalt pavement. However, the fatigue test results analyzed by various test methods have a quite significant divergence, which represents a lack of accuracy to access the durability of rubber asphalt mixture objectively. Thus, in the structural resistance design of rubber asphalt pavement, there exists a problem of artificial randomness of fatigue parameters. Hence, the primary objective of this study is to improve the procedure for determining the structural resistance of rubber asphalt pavement. To this end, the direct tensile, unconfined compressive, and indirect tensile strength tests of rubber asphalt mixture were performed under various loading rates to reveal the velocity-dependent of the strength of rubber asphalt mixture. The model of direct tensile strength, unconfined compressive strength, and indirect tensile strength increasing with loading rate are SD=7.772v0.205, SC=1.748v0.204, and ST=1.077v0.207, respectively. The stress ratio related to both the traditional S-N fatigue equation and the loading rate was defined as the standard stress ratio and the velocity-dependent stress ratio, respectively. The fatigue test of rubber asphalt mixture was conducted. The results from those experiments were analyzed. A fatigue equation (Nf=tv-5.129 R2=0.853) related to the loading rate was established. The results indicated that the viscoelastic characteristics of rubber asphalt mixture are not taken into consideration in the traditional S-N fatigue equation, which contributed to the non-uniqueness and uncertainty of fatigue test results. The viscoelastic characteristics of rubber asphalt mixture are considered by the fatigue equation related to the velocity-dependent stress ratio. Thus, a new method (Kv=Nf0.0958) considering the influence of the loading rate for calculating the strength structure coefficient of the rubber asphalt mixture was proposed. The effectiveness and completeness of the mechanical behavior of pavement structure characterized by material parameters were improved. Thus, the utilization rate of waste rubber for pavement construction can be significantly increased and the life cycle cost of asphalt pavement is reduced.

Fatigue characteristics of cement-stabilized steel slag base course for asphalt pavement structure considering different paving methods

Laboratory Evaluation On The Performance Of Porous Asphalt Mixture With Steel Slag For Seasonal Frozen Regions

Structural Mechanics Analysis of Asphalt Pavement Using Large Stone Asphalt Mixture As Base

Analysis of the Fatigue Crack Propagation Process of the Stress-Absorption Layer of Composite Pavement Based on Reliability

A Novel Approach for the Mechanical Response of Cement Concrete Pavement Structure Considering the Interlaminar Interface Shear Slip Effect

Inverse Engineering Stress-Dependent Resilient Moduli of Cement-Treated Base Materials in Asphalt Pavements Using Falling Weight Deflectometer

Field Measurement and Analysis on the Mechanical Response of Asphalt Pavement Using Large-Particle-Size Crushed Stone Base Treated with Fly Ash and Slag Powder

Optimizing the Utilization of Steel Slag in Cement-Stabilized Base Layers: Insights from Freeze–Thaw and Fatigue Testing

Investigation of Permanent Deformation Behavior of Steel Slag Asphalt Mixture under Indoor Simulation

Mechanical Properties and Durability of Steel Slag-mineral Powder-coal Gangue Mixture by Uniform Design for Pavement Base

Study on fatigue performance of asphalt mixture in service life based on accelerated loading test

Experimental Study on Subgrade Material of Calcium Silicate Slag

Microstructural Analysis of the Effects of Compaction on Fatigue Properties of Asphalt Mixtures

Study on Road Performance of Cement Fly Ash Stabilized Steel Slag-Concrete Recycled Macadam

Study on mechanical properties of traffic pavement materials under fatigue loading

Fatigue performance of interface bonding between asphalt pavement layers using four-point shear test set-up

Macroscopic properties and microscopic characterisation of an optimally designed anti-cracking stone base course filled with cement stabilised macadam

Unified characterizing fatigue performance of rubberized asphalt mixtures subjected to different loading modes

Study on pavement performance of steel slag asphalt mixture based on surface treatment

Analysis of Asphalt Mixtures Modified with Steel Slag Surface Texture Using 3D Scanning Technology

Adaptability of Asphalt Pavement Structures to Deformation of Embankment Underlain by Black Cotton Soil