Abstract:For all‐solid‐state batteries with carbon nanoparticle‐based deposition‐type anode, the discharge capacity can be significantly increased by either active stack pressure control or by hot pressing of binder‐containing anode and separator. High discharge capacities exceeding 190 mAh g−1 are achieved at room temperature without using any expensive elements (thiophosphate‐based solid electrolyte, Ni‐rich NMC cathode active material). The concept of using metallic lithium as anode material offers great potential for increasing the energy density of lithium‐ion batteries (LIBs). However, the ubiquitous formation of dendrites during lithium plating has prevented this so far. This is also true for all‐solid‐state batteries (ASSBs), for which dendrite formation has been observed particularly at high stack pressures and high current densities. An evolving and very promising strategy for suppressing dendrite formation is the usage of a thin carbon layer on the anode side, referred to as deposition‐type lithium metal anode. Here, it is shown that for ASSBs with carbon‐based deposition‐type anodes of this type, the discharge capacity can be significantly increased by either: i) active stack pressure control; or by ii) hot pressing of binder‐containing anode and separator. High discharge capacities exceeding 190 mAh g−1 are achieved at room temperature without using any expensive elements (thiophosphate‐based solid electrolyte, Ni‐rich NMC cathode active material). This observation points to the importance of ensuring good mechanical contact between the deposition‐type anode and the separator during cycling. While approach (i) is readily applicable for lab‐scale batteries, approach (ii) should be a promising option for future commercial ASSBs.

Solid-state lithium battery cathodes operating at low pressures

LiNi0.5Mn1.5O4 cathode microstructure for all-solid-state batteries

LiNi 0.5 Mn 1.5 O 4 Cathode Microstructure for All-Solid-State Batteries.

The effect of volume change and stack pressure on solid‐state battery cathodes

Cobalt-free cathodes and silicon thin-film anodes towards high-capacity solid-state batteries

LiAlO2-coated LiNi0.8Co0.1Mn0.1O2 and chlorine-rich argyrodite enabling high-performance all-solid-state lithium batteries at suitable stack pressure

A Solid‐State Battery Cathode with a Polymer Composite Electrolyte and Low Tortuosity Microstructure by Directional Freezing and Polymerization

Breaking free from high pressure

A solid-state lithium-ion battery with micron-sized silicon anode operating free from external pressure

Deposition‐Type Lithium Metal All‐Solid‐State Batteries: About the Importance of Stack‐Pressure Control and the Benefits of Hot Pressing during Initial Cycling

Achieving stable all-solid-state lithium-metal batteries by tuning the cathode-electrolyte interface and ionic/electronic transport within the cathode

Stack Pressure Considerations for Room Temperature All-Solid-State Lithium Metal Batteries

Electro-chemo-mechanical design of polymer matrix in composited LiNi0.8Co0.1Mn0.1O2 cathode endows solid-state batteries with superior performance

Stable performance of an all-solid-state Li metal cell coupled with a high-voltage NCA cathode and ultra-high lithium content poly(ionic liquid)s-based polymer electrolyte

Lithium Argyrodite as Solid Electrolyte and Cathode Precursor for Solid‐State Batteries with Long Cycle Life

A Novel Solid-State Li-O-2 Battery With An Integrated Electrolyte And Cathode Structure

High Capacity and Rate Performance of LiNi0.5Co0.2Mn0.3O2composite Cathode for Bulk-Type All-Solid-state Lithium Battery

Quasi-Solid-State Lithium Metal Batteries Using the LiNi0.8Co0.1Mn0.1O2-Li1+ xAlxTi2- x(PO4)3 Composite Positive Electrode

High-energy all-solid-state lithium batteries enabled by Co-free LiNiO 2 cathodes with robust outside-in structures

High-energy All-Solid-state Lithium Batteries Enabled by Co-free LiNiO2 Cathodes with Robust Outside-in Structures.

Synergistic Evolution of Alloy Nanoparticles and Carbon in Solid-State Lithium Metal Anode Composites at Low Stack Pressure