Abstract:OBJECTIVE This study aimed at determining the influence of hydrofluoric acid (HF) in varied concentrations on the surface morphology of lithium disilicate glass ceramics and bond durability between resin composites and post-treated lithium disilicate glass ceramics. METHODS After being sintered, ground, and washed, 72 as-prepared specimens of lithium disilicate glass ceramics with dimensions of 11 mm×13 mm×2 mm were randomly divided into three groups. Each group was treated with acid solution [32% phosphoric acid (PA) or 4% or 9.5% HF] for 20 s. Then, four acidified specimens from each group were randomly selected. One of the specimens was used to observe the surface morphology using scanning electron microscopy, and the others were used to observe the surface roughness using a surface roughness meter (including Ra, Rz, and Rmax). After treatment with different acid solutions in each group, 20 samples were further treated with silane coupling agent/resin adhesive/resin cement (Monobond S/Multilink Primer A&B/Multilink N), followed by bonding to a composite resin column (Filtek™ Z350) with a diameter of 3 mm. A total of 20 specimens in each group were randomly divided into two subgroups, which were used for measuring the microshear bond strength, with one of them subjected to cool-thermal cycle for 20 000 times. RESULTS The surface roughness (Ra, Rz, and Rmax) of lithium disilicate glass ceramics treated with 4% or 9.5% HF was significantly higher than that of the ceramic treated with PA (P<0.05). The lithium disilicate glass ceramics treated with 9.5% HF also demonstrated better surface roughness (Rz and Rmax) than that of the ceramics treated with 4% HF. Cool-thermal cycle treatment reduced the bond strength of lithium disilicate glass ceramics in all groups (P<0.05). After cool-thermal cycle, the lithium disilicate glass ceramics treated with HF had higher bond strength than that of the ceramics treated with PA. The lithium disilicate glass ceramics treated with 4% HF had higher bond strength than that of the ceramics treated with 9.5% HF (P<0.05). During cool-thermal cycle, the lithium disilicate glass ceramics treated with 4% HF demonstrated higher reduction in bond strength than that of the samples treated with 9.5% HF (P<0.05). CONCLUSIONS The concentration of HF significantly affected the surface morphology of lithium disilicate glass ceramics and the bond durability between resin composites and post-treated lithium disilicate glass ceramics. The bond strength between resin composites and post-treated lithium disilicate glass ceramic was more efficiently maintained by treatment with 9.5% HF.

Bank competition and ECB ' s monetary policy q

Effects of Incorporation of Nano-Fluorapatite or Nano-Fluorohydroxyapatite on a Resin-Modified Glass Ionomer Cement

A new ring signature scheme with signer-admission property

Effect of sandblasting on the shear bond strength and durability of three resin cements bonded to titanium

Self-etching primer versus hydrofluoric acid and air-abrasion: effects on flexural and resin bond strengths of resin-based CAD/CAM material

Enhancing adhesive bond strength of CFRP/titanium joints through NaOH anodising and resin pre-coating treatments with optimised anodising conditions

[Pay attention to IgG4-related lung disease].

Effect of Selective Laser Melting Pure Titanium on Bond Strength of Titanium to Composite Resin by Different Surface Treatments

SYSTEMIC INFLAMMATION INCREASES INTESTINAL PERMEABILITY DURING EXPERIMENTAL HUMAN ENDOTOXEMIA

Comparative Study of Resin and Silane Coupling Agents Coating Treatments on Bonding Strength Improvement of Titanium and Carbon Fiber Composites

Effect of Hydrofluoric Acid Etching Time on the Resin Bond Durability of Glass Ceramic

QUALIDEM: development and evaluation of a dementia specific quality of life instrument––validation

Adhesive Bonding to Dentin with Ferrous Chloride Primers and Tri-n-butylborane-initiated Luting Agents

The Effect of Intraoral Sandblasting on the Bond Strength Between Ni-Cr Alloy and Composite Resin

Improving the bonding stability between resin cements and zirconia-based ceramic using different surface treatments

The Effects of Combined Treatments of Laser Engraving, Plasma Spraying and Resin Pre-Coating on Improving the Bonding Strength of Titanium Alloy and Carbon Fiber-Reinforced Polymer

The Effect of Surface Treatments on Shear Bond Strength between Orthodontic Metal Bracket and Porcelain Face

Vitamin E status and metabolism in adult and aged aryl hydrocarbon receptor null mice.

Shear Bond Strength of Three Resin Cements to the Casting Pure Titanium

In vitro short-term bonding performance of zirconia treated with hot acid etching and primer conditioning

[Effect of Hydrofluoric Acid Concentration on the Surface Morphology and Bonding Effectiveness of Lithium Disilicate Glass Ceramics to Resin Composites].