Vitamin E status and metabolism in adult and aged aryl hydrocarbon receptor null mice.

M. Traber,D. Mustacich,L. Sullivan,S. Leonard,A. Ahern-Rindell,N. Kerkvliet

DOI: https://doi.org/10.1016/j.jnutbio.2009.10.005

2010-12-01

Abstract:

What problem does this paper attempt to address?

Adhesion to lithium disilicate glass-ceramics after aging: Resin viscosity and ceramic surface treatment effects

Kiara Serafini Dapieve,Rafaela Oliveira Pilecco,Renatta Wrasse Temp,Marcos Antonio Villetti,Gabriel Kalil Rocha Pereira,Luiz Felipe Valandro

DOI: https://doi.org/10.1016/j.jmbbm.2023.105819

Abstract:Objective: To evaluate the influence of intaglio ceramic surface treatments, resin cement viscosities, and storage regimens on the microshear bond strength of lithium disilicate ceramic. In addition, to investigate the dynamic viscosity of the resin-based luting agents. Materials and methods: Ceramic slices were randomly allocated into eight groups (n = 19) considering three factors: ceramic surface treatment (hydrofluoric acid followed by silane, HF; or self-etching ceramic primer, E&P), resin cement viscosity (high, HIGH; or low, LOW) and storage regimen (baseline or aging). Surface treatments were performed, resin cement cylinders were built and microshear bond strength tests (μSBS, wire-loop method, speed: 1.0 mm/min) were run according to the storage factor. Failure mode, topographic and dynamic viscosity (37 °C; shear rate of 1.0-100 s-1) of resin cement components (base, high and low catalyst) were also performed. Results: Resin cement viscosity and the association among ceramic surface treatment, resin cement viscosity, and storage regimen were statistically significant factors (p < 0.05). Worse behavior was identified for the E&P_HIGH group compared to the E&P_LOW and HF_LOW in the baseline condition. After aging, the HF_HIGH group (16.78 MPa) presented the worst result among the aged groups (21.44-25.25 MPa). Most of the failures were adhesive. Surface micrographs revealed a distinct pattern after etching, more aggressive by HF and milder by E&P. High viscosity catalyst is 5.3 and 8.5-fold more viscous than the base and low viscosity catalyst, respectively (high > base > low). Conclusion: Differences in filler content can impact the resin viscosity of the material (more fillers increase the viscosity), which in turn can influence the bond strength of a lithium disilicate ceramic, depending on the surface treatment and storage regimen.
The Influence of Hydrofluoric Acid Temperature and Application Technique on Ceramic Surface Texture and Shear Bond Strength of an Adhesive Cement

Cristiana Cuzic,Anca Jivanescu,Radu Marcel Negru,Iosif Hulka,Mihai Rominu

DOI: https://doi.org/10.3390/ma16124303

IF: 3.4

2023-06-10

Materials

Abstract:All-ceramic restorations are the foundation of modern esthetic dentistry. Clinical approaches for preparation, durability, aesthetics, and repair have been reformed by the idea of adhesive dentistry. The aim of the study and the objective question was to evaluate the impact of heated hydrofluoric acid pretreatment and the application technique's influence on the surface morphology and roughness of leucite-reinforced glass–ceramic materials (IPS Empress CAD, Ivoclar Vivadent), which is fundamental for understanding the adhesive cementation process. Scanning electron microscopy was used to observe the effectiveness of the two HF (Yellow Porcelain Etch, Cerkamed) application techniques and the HF's temperature impact on the surface topography of the ceramic. Based on surface conditioning methods, the adhesive cement (Panavia V5, Kuraray Noritake Dental Inc., Tokyo, Japan) was applied to the conditioned ceramic samples and light-cured. Shear bond strength values were correlated with the micro-retentive surface texture of the ceramic. With universal testing equipment at a 0.5 mm/min crosshead speed, SBS values between the resin cement and the ceramic material were assessed until failure. Analyzing the fractured surfaces of the specimens by digital microscopy, the failure modes were divided into three categories: adhesive, cohesive, and mixed failure. Analysis of variance (ANOVA) was used to statistically analyze the collected data. The results show that alternative treatment methods affected the material's surface characteristics and have an influence on the shear bond strength.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,metallurgy & metallurgical engineering
Effect of Hydrofluoric Acid Etching Time on the Resin Bond Durability of Glass Ceramic

Xiang-feng Meng,Xiao-lu Zhou,Xiao-ping Luo

DOI: https://doi.org/10.3760/cma.j.issn.1002-0098.2010.05.014

2010-01-01

Abstract:OBJECTIVE:To analyze the effect of hydrofluoric acid (HFA) etching time on the resin bond durability of glass ceramic.METHODS:Three groups of samples of machinable glass ceramic (ProCAD) were etched by 4.8% HFA for 0, 30 and 60 s respectively. The roughness parameters (Ra, Sm, S) and surface area of the samples, were measured with a 3D-laser scanning microscope. Then the ceramic surfaces were bonded with four resin cements (silane coupler/resin cement), which were Monobond S/Variolink II, Clearfil Ceramic Primer/Clearfil Esthetic Cement, GC Ceramic Primer/Linkmax HV, and Porcelain Liner M/SuperBond. The micro-bond strengths between the ceramic and the resin were tested at baseline and after the samples had been treated in 30000 thermal cycles.RESULTS:The Ra [(3.89+/-1.94), (12.53+/-0.80), (13.58+/-1.10) microm] and surface area [(7.81+/-2.96), (30.18+/-2.05), (34.16+/-1.97) mm2] of ceramic increased with the increase of HFA etching time. The thermal cycling test reduced the bond strength of all test groups. The bond strength of Monobond S/Variolink II group [(3.59+/-3.51), (16.18+/-2.62), (20.33+/-2.45) MPa] and Clearfil Ceramic Primer/Clearfil Esthetic Cement group [(4.74+/-2.08), (7.77+/-1.55), (13.45+/-3.75) MPa] increased with the increase of HFA etching time; 30 s HFA etching group of Porcelain Liner M/SuperBond had higher bond strength [(22.00+/-1.64) MPa] than its 0 s HFA etching group [(12.96+/-4.17) MPa], and no significant difference was found between the 30 s and 60 s HFA etching groups of Porcelain Liner M/SuperBond [(20.42+/-3.01) MPa]. HFA etching time had no effect on the bond strength of GC Ceramic Primer/Linkmax HV.CONCLUSIONS:HFA etching can improve the resin bond durability of glass ceramic, and the etching time is not only related to the change of ceramic surface roughness and area, but also to the characteristics of resins.
Effect of Etching Time and Resin Bond on the Flexural Strength of IPS E.max Press Glass Ceramic.

Luo Xiaoping,Ren Dongfeng,Nick Silikas

DOI: https://doi.org/10.1016/j.dental.2014.08.373

IF: 5.687

2014-01-01

Dental Materials

Abstract:Objectives. To evaluate the effect of hydrofluoric acid (HFA) etching time and resin cement bond on the flexural strength of IPS e.max (R) Press glass ceramic.Methods. Two hundred and ten bars, 25 mm x 3 mm x 2 mm, were made from IPS e.max (R) Press ingots through lost-wax, hot-pressed ceramic fabrication technology and randomly divided into five groups with forty-two per group after polishing. The ceramic surfaces of different groups were etched by 9.5% hydrofluoric acid gel for 0, 20, 40, 60 and 120 s respectively. Two specimens of each group were selected randomly to examine the surface roughness and 3-dimensional topography with atomic force microscope (AFM), and microstructure was analyzed by the field emission scanning electron microscope (FE-SEM). Then each group were subdivided into two subgroups (n = 20). One subgroup of this material was selected to receive a thin (approximately 0.1 mm) layer of resin luting agent (Variolink N) whereas the other subgroup remained unaltered. Half of subgroup's specimens were thermocycled 10,000 times before a 3-point bending test in order to determine the flexural strength. Interface between resin cement and ceramic was examined with field emission scanning electronic microscope.Results. Roughness values increased with increasing etching time. The mean flexural strength values of group 0 s, 20 s, 40 s, 60 s and 120 s were 384 +/- 33, 347 +/- 43, 330 +/- 53,327 +/- 67 and 317 +/- 41 MPa respectively. Increasing HF etching times reduced the mean flexural strength (p < 0.05). However, the mean flexural strength of each group, except group 0 s, increased significantly to 420 +/- 31, 435 +/- 50, 400 +/- 39 and 412 +/- 58 MPa after the application of dual-curing resin cement. In the present investigation, no significant differences after thermocycling on the flexural strengths were evident.Significance. Overtime HF etching could have a wakening effect on IPS e.max (R) Press glass ceramic, but resin cement bonding to appropriately etched surface would strengthen the dental ceramic. (C) 2014 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.
Effect of Hydrothermal Aging on the Flexural Strength and Microhardness of Materials Used for Additive or Subtractive Manufacturing of Definitive Restorations

Deniz Yılmaz,Gülce Çakmak,Mehmet Esad Güven,Stefano Pieralli,Hyung-In Yoon,Marta Revilla-León,Burak Yilmaz

DOI: https://doi.org/10.11607/ijp.8847

2024-02-21

Abstract:Purpose: To evaluate the flexural strength (FS) and microhardness of various CAD/CAM restorative materials intended for definitive use. The effect of hydrothermal aging on the mechanical properties of these materials was also investigated. Materials and methods: A total of 210 bar-shaped specimens (17 × 4 × 1.5 mm ± 0.02 mm) were fabricated via either subtractive manufacturing (SM) methods-reinforced composite resin (SM-CR), polymer-infiltrated ceramic network (SM-PICN), fine-structured feldspathic ceramic (SMFC), nanographene-reinforced polymethyl methacrylate (PMMA; SM-GPMMA), PMMAbased resin (SM-PMMA)-or additive manufacturing (AM) methods with urethane acrylate-based resins (AM-UA1 and AM-UA2). Specimens were then divided into two subgroups (nonaged or hydrothermal aging; n = 15). A three-point flexural strength test was performed, and five specimens from the nonaged group were submitted to microhardness testing. Specimens were subjected to 10,000 thermal cycles, and the measurements were repeated. Results: Regardless of aging, SM-CR had the highest FS (P < .001), followed by SM-GPMMA (P ≤ .042). In nonaged groups, AM-UA2 had a lower FS than all other materials except SM-FC (P = 1.000). In hydrothermal aging groups, AM specimens had lower FS values than other materials, except SM-PMMA. With regard to microhardness, there was no significant difference found between any of the tested materials (P ≥ .945) in the nonaged and hydrothermal aging groups. Conclusions: The effect of hydrothermal aging on FS varied depending on the type of restorative material. Regardless of aging condition, SM-CR showed the highest FS values, whereas SM-FC had the highest microhardness. Hydrothermal aging had no significant influence on the microhardness of the tested materials.
[Effect of Hydrofluoric Acid Etching Time and Resin Bonding on the Flexural Strength of Lithium Disilicate Glass Ceramic].

Dong-feng Ren,Xiao-ping Luo

DOI: https://doi.org/10.3760/cma.j.issn.1002-0098.2013.08.004

2013-01-01

Abstract:OBJECTIVE:To analyze the effect of hydrofluoric acid(HFA) etching time and resin bonding on the flexural strength of IPS e.max® Press glass ceramic, and evaluate the efficacy of resin cements to seal the cracks of the etched ceramic.METHODS:Two hundred and twenty-five bars (25.0 mm×3.0 mm×2.0 mm) were made from IPS e.max® Press ingots using lost-wax, hot-pressed ceramic fabrication technology and randomly divided into five groups, forty-five each.In each group, the surfaces of ceramic bars were etched by 9.5% HFA gel for 0, 20, 40, 60 and 120 s respectively. Three specimens from each group were selected to observe the microstructure by the field emission scanning electron microscope (FE-SEM). Then each group were randomly subdivided into two subgroups (n = 20).One subgroup were coverd with a thin (approximately 0.1 mm) layer of resin cement (Variolink N), whereas the other subgroup remained unaltered.Half of the specimens were stored in 37°C water bath for 24 h and the other half went through thermocycle 10 000 times before 3-point bending test to determine their flexural strength.Interfaces between resin cement and etched ceramic were examined with FE-SEM.RESULTS:FE-SEM results showed that etching with HFA resulted in preferential dissolution of glass ceramic, and partially supported crystals within the glass matrix were lost with the increasing of etching time.FE-SEM indicated that resin cement sealed the cracks and defects and bonded tightly to etched ceramic surface. The mean flexural strength values of group 0, 20, 40, 60 and 120 s were (384 ± 33), (347 ± 43), (330 ± 53), (327 ± 67) , and (317 ± 41) MPa respectively. The mean flexural strength of each group except group 0 s increased significantly to (420 ± 31), (435 ± 50), (400 ± 39), and (412 ± 58) MPa respectively after the application of resin cement.CONCLUSIONS:Overtime HFA etching could have a wakening effect on IPS e.max® Press glass-ceramic. The application of dual-curing resin cement can compensate the strength loss of the etched glass ceramic.
[Effect of Hydrofluoric Acid Concentration on the Surface Morphology and Bonding Effectiveness of Lithium Disilicate Glass Ceramics to Resin Composites].

Qian Hailan,Ren Lingyan,Nie Rongrong,Meng Xiangfeng

DOI: https://doi.org/10.7518/hxkq.2017.06.006

2017-01-01

Abstract:OBJECTIVE This study aimed at determining the influence of hydrofluoric acid (HF) in varied concentrations on the surface morphology of lithium disilicate glass ceramics and bond durability between resin composites and post-treated lithium disilicate glass ceramics. METHODS After being sintered, ground, and washed, 72 as-prepared specimens of lithium disilicate glass ceramics with dimensions of 11 mm×13 mm×2 mm were randomly divided into three groups. Each group was treated with acid solution [32% phosphoric acid (PA) or 4% or 9.5% HF] for 20 s. Then, four acidified specimens from each group were randomly selected. One of the specimens was used to observe the surface morphology using scanning electron microscopy, and the others were used to observe the surface roughness using a surface roughness meter (including Ra, Rz, and Rmax). After treatment with different acid solutions in each group, 20 samples were further treated with silane coupling agent/resin adhesive/resin cement (Monobond S/Multilink Primer A&B/Multilink N), followed by bonding to a composite resin column (Filtek™ Z350) with a diameter of 3 mm. A total of 20 specimens in each group were randomly divided into two subgroups, which were used for measuring the microshear bond strength, with one of them subjected to cool-thermal cycle for 20 000 times. RESULTS The surface roughness (Ra, Rz, and Rmax) of lithium disilicate glass ceramics treated with 4% or 9.5% HF was significantly higher than that of the ceramic treated with PA (P<0.05). The lithium disilicate glass ceramics treated with 9.5% HF also demonstrated better surface roughness (Rz and Rmax) than that of the ceramics treated with 4% HF. Cool-thermal cycle treatment reduced the bond strength of lithium disilicate glass ceramics in all groups (P<0.05). After cool-thermal cycle, the lithium disilicate glass ceramics treated with HF had higher bond strength than that of the ceramics treated with PA. The lithium disilicate glass ceramics treated with 4% HF had higher bond strength than that of the ceramics treated with 9.5% HF (P<0.05). During cool-thermal cycle, the lithium disilicate glass ceramics treated with 4% HF demonstrated higher reduction in bond strength than that of the samples treated with 9.5% HF (P<0.05). CONCLUSIONS The concentration of HF significantly affected the surface morphology of lithium disilicate glass ceramics and the bond durability between resin composites and post-treated lithium disilicate glass ceramics. The bond strength between resin composites and post-treated lithium disilicate glass ceramic was more efficiently maintained by treatment with 9.5% HF.
Fatigue failure load of zirconia-reinforced lithium silicate glass ceramic cemented to a dentin analogue: Effect of etching time and hydrofluoric acid concentration

Jaiane Bandoli Monteiro,Marcelo Gallo Oliani,Luis Felipe Guilardi,Catina Prochnow,Gabriel Kalil Rocha Pereira,Marco Antonio Bottino,Renata Marques de Melo,Luiz Felipe Valandro

DOI: https://doi.org/10.1016/j.jmbbm.2017.09.028

Abstract:This study aimed to evaluate the effect of etching time and hydrofluoric acid (HF) concentration on the fatigue failure load and surface characteristics of zirconia-reinforced lithium silicate glass (ZLS) ceramic cemented to a dentin-like, fiber reinforced epoxy resin. Ceramic (Suprinity, VITA) (1.0mm thick) and epoxy resin (2.5mm thick) discs (10mm diameter) were produced. The bonding surface of the ceramic samples was nonetched (control group), or etched for 30, 60 or 90s by 5% or 10% HF. The epoxy resin discs were etched by 10% HF for 30s followed by the application of an adhesive material (Single Bond Universal, 3M ESPE). Pairs of ceramic/epoxy resin discs were cemented with a dual cure resin cement. The fatigue failure load was determined by the staircase method (500,000 cycles at 20Hz; initial load = 925N; step size = 45N). In 10% HF the etching time was shown to influence the fatigue failure load, which increased as the etching time increased (30s < 60s < 90s), and in 5% HF the fatigue failure load was not shown to be affected by the etching time; the lowest fatigue failure loads were produced in the control group without ceramic etching followed by 10% HF acid etching for 30s. Topography analysis showed variations based on the etching protocols. All fractures (radial cracks) were shown to originate from defects at the ceramic surface on the cementing interface. For fatigue loading improvements of ZLS ceramic, 10% HF acid etching for 90s and silanization of the ceramic surface is recommended.
Recycling CAD/CAM Lithium Disilicate Ceramic: Effect of Surface Treatment and Aging on the Bond Strength to Resin Cement

Larissa Mendonça de Miranda,Aparecida Tharlla Leite Caldas,Dayanne Monielle Duarte Moura,Karina Barbosa Souza,Isauremi Vieira de Assunção,Mutlu Özcan,Rodrigo Othávio de Assunção E Souza

DOI: https://doi.org/10.11607/ijp.8677

2024-11-22

Abstract:Purpose: To investigate the effects of recycling lithium disilicate (LD), surface treatment, and thermocycling on the bond strength to resin cement. Materials and methods: A total of 72 tablets (10 × 10 × 3 mm) of LD were made according to the recycling cycle with 24 tablets for each strategy: control (conventional sintering), 1R (1 recycling cycle), and 3R (3 recycling cycles). For the recycling groups, tablets were waxed, mounted in a silicone ring, and poured with investment material, and residues of sintered LD tablets were pressed by the lost wax technique. The residual LD was reused as described until it reached 3R. Afterward, the tablets were embedded in acrylic resin, sanded, and divided (n = 15) according to the factors of 'surface treatment' (hydrofluoric acid [HF] for 20 seconds [HF20s] and silane, HF for 120 seconds [HF120s] and silane, and Monobond Etch & Prime [MEP]) and thermocycling (TC; with 10,000 cycles and without). After surface treatment, cylinders (diameter: 2 mm) of resin cement were made and submitted to SBS test (100 kgf, 1 mm/minute). Data (MPa) were analyzed by three-way ANOVA, Tukey test (5%), and Weibull analysis. Failure analysis was performed with a stereomicroscope. Results: ANOVA revealed that all factors were significant (P = .000*). The group 3RMEP (105.09 ± 19.49) presented the highest SBS among the experimental groups. The 1RHF20sTc (7.50 ± 1.97) group had the lowest SBS, similar to CHF20sTc (15.69 ± 3.77), 1RHF20s (15.12 ± 3.03), 1RHF120sTc (14.60 ± 3.43), and 3RHF20sTc (15.65 ± 0.97). The Weibull modulus and characteristic strength varied among the experimental groups (P = .0). Failure analysis revealed adhesive and mixed types. Conclusions: The recycling of DL ceramics increases the SBS to resin cement when the ceramic is treated with HF120s and silane or MEP.
Effect of Resin Cement Viscosities and Surface Roughness on Shear Bond Strength of Conditioned Polymer Infiltrated Ceramic Network

Khaled M. Alzahrani

DOI: https://doi.org/10.1016/j.pdpdt.2024.104333

IF: 3.577

2024-09-08

Photodiagnosis and Photodynamic Therapy

Abstract:Background Hybrid ceramics bonding with the dentinal substrate is crucial for clinical success and longevity. To enhance adhesion, the surface of ceramic restorations is modified through various conditioning techniques Aim Effect of Different Surface Conditioners Erbium-doped yttrium aluminum garnet (ER: YAG) laser and Low-level laser therapy (LLLT) activated Methylene blue (MB) on the surface roughness (Ra) and shear bond strength (SBS) of Polymer infiltrating ceramic network (PICN) discs bonded using different viscosity resin cement before and after thermal aging. Material and Methods One hundred and fifty human central incisors and one hundred and fifty-three PICN discs were prepared. PICN discs were randomly allocated into three groups based on the surface conditioning(n=51) Group 1:10% HF acid-S, Group 2: LLLT (MB), and Group 3: Er: YAG laser. Following conditioning Ra scores of ten samples were performed. Surface topography of samples was performed using a scanning electron microscope (SEM). Bonding of forty PICN discs from each conditioning group was performed with high (A) or low viscosity (B) dual-curing resin cement (n= 20 each). Each subgroup was divided into two cohorts and subjected to varying storage conditions. The SBS test and failure mode analysis were performed using a universal testing machine and stereomicroscope. Descriptive statistics of SBS and Ra for each group were analyzed using ANOVA and Tukey post hoc tests. HF acid-S attained the highest Ra scores. Results Group 1A (HF-S+HIGH) samples achieved the highest SBS values at baseline. Group 3A, on the other hand, displayed the lowest bond score (Er: YAG laser+HIGH) after thermal aging Intergroup comparison analysis at baseline unveiled that Group 1A and Group 1B (HF(S) + LOW) displayed no significant difference in their bond strength scores (p>0.05). Following artificial aging, it was observed that Group 2A (LLLT (MB) + HIGH) and Group 3A (Er:YAG laser + HIGH) ) presented comparable SBS(p>0.05). Thermal aging decreased SBS significantly in all groups. PICN conditioned with HF-S results in high surface roughness. Conclusion PICN conditioned with HF acid with silane and bonded with low-viscosity resin cement to the dentinal substrate is preferable. Aging influences SBS.

oncology
Biaxial flexural strength of hydrothermally aged resin-based materials

Rodrigo Ricci Vivan,Mariana Miranda de Toledo Piza,Bruna de Mello Silva,Thalya Fernanda Horsth Maltarollo,Gustavo Sivieri-Araujo,Murilo Priori Alcalde,Marco Antonio Hungaro Duarte,Estevam Augusto Bonfante,Henrico Badaoui Strazzi-Sahyon

DOI: https://doi.org/10.1016/j.jmbbm.2024.106568

IF: 4.042

2024-05-05

Journal of the Mechanical Behavior of Biomedical Materials

Abstract:Purpose The strength of temporary restorations plays a vital role in full-mouth reconstruction, and it can be impacted by the aging process. The aim of this in vitro study was to evaluate the biaxial flexural strength and fractographic features of different resin-based materials submitted to thermal aging. Material and Methods One hundred and ninety-two resin disc-shaped specimens (6.5 mm in diameter and 0.5 mm in thickness) were fabricated and divided into six experimental groups according to the resin-based materials (Filtek Bulk-Fill flowable resin; J-Temp temporary resin; and Fuji Lining glass ionomer cement) and aging process (before and after thermal cycling). Biaxial flexural strength test was performed using a universal testing machine at a crosshead speed of 0.5 mm/min before and after thermal cycling (5°C and 55°C, 5760 cycles, 30 seconds). The mechanical properties were assessed using Weibull parameters (characteristic strength and Weibull modulus) (n=30). Fractured specimens were examined under a polarized light stereomicroscope to identify crack origin and propagation direction. The surface microstructure of the resin-based materials was assessed by scanning electron microscopy (n=2). The Weibull modulus ( m ), characteristic strength, and reliability properties were calculated, and a contour plot was used to detect differences among groups (95% confidence interval). Results The Weibull modulus ( m ), characteristic strength, and reliability of the resin-based compounds were influenced by material type and thermal aging (p < 0.05). Weibull modulus ( m ) revealed no differences when comparing the materials and aging process (p > 0.05), except for the preceding aging period where Filtek Bulk-Fill exhibited higher values compared to J-Temp (p < 0.05). Filtek Bulk-Fill demonstrated superior characteristic strength and reliability compared to J-Temp and Fuji Lining before and after thermal cycling (p < 0.05). Fractography of the resin-based materials showed fractures originating from surface defects exposed to tensile side and their propagation toward the compressive side. Generally, no differences in surface microstructure were observed on micrographs before and after thermal aging for Filtek Bulk-Fill and Fuji Lining. However, the aging process developed flaws in J-Temp. Conclusion Resin-based material composition resulted in different flexural strength performance, impacting the Weibull modulus ( m ), characteristic strength, and reliability of the resin-based restorations.

engineering, biomedical,materials science, biomaterials
Bond Strength to Lithium-Disilicate Ceramic after Different Surface Cleaning Approaches

Federico Del Bianco,Claudia Mazzitelli,Tatjana Maravic,Uros Josic,Federica Florenzano,Paolo Baldissara,Lorenzo Breschi,Annalisa Mazzoni

DOI: https://doi.org/10.3290/j.jad.b4874329

2024-01-19

Abstract:Purpose: To evaluate the effect of different lithium-disilicate (LiSi) glass-ceramic surface decontamination procedures on the shear bond strength (SBS) to resin cement. Materials and methods: Seventy CAD/CAM LiSi ceramic specimens (IPS e.max CAD, Ivoclar) were cut and sintered. Fifty specimens were treated with 5% hydrofluoric acid (HF) for 20 s, while 20 were left untreated. All 70 specimens were then contaminated with human saliva and try-in silicone paste. The following surface cleaning methods were investigated (n = 10): C: water rinsing (control); PA: 37% H3PO4 etching for 20 s; E: 70% ethanol applied for 20 s; CP: cleaning paste (Ivoclean, Ivoclar) brushed for 20 s; HFSEP: self-etching ceramic primer (Monobond Etch&Prime, Ivoclar) rubbed for 20 s; HF: 5% HF applied for 20 s or no HF etching prior to contamination; SEP: self-etching ceramic primer rubbed for 20 s and no HF etching prior to contamination. Composite cylinders were created and luted with an adhesive resin cement to the decontaminated surfaces. After storage for 24 h at 37°C, the SBS test was conducted. Two fractured specimens per group were observed under SEM to perform fractographic analysis. The data were statistically analyzed with p set at <0.05. Results: The type of surface cleaning approach influenced bond strength (p < 0.001). HFSEP, SEP, and HF attained higher SBS (p < 0.001) compared to other groups. None of the approaches were able to completely remove contaminants from the ceramic surfaces. SEM images showed residual traces of contaminants on CP-treated surfaces. Conclusions: The self-etching ceramic primer enhanced bond strength to contaminated LiSi ceramic surfaces, irrespective of previous treatment with hydrofluoric acid.
Surface morphology and mechanical properties of conventional and self-adhesive resin cements after aqueous aging.

Yahui Pan,Xiaodong Xu,Fangfang Sun,Xiangfeng Meng

DOI: https://doi.org/10.1590/1678-7757-2017-0449

2019-01-01

Journal of Applied Oral Science

Abstract:The stable long-term performance of resin cement under oral environmental conditions is a crucial factor to obtain a satisfactory success of the allceramic dental restoration. Objective: This study aimed at evaluating and comparing the surface morphology and mechanical property of conventional and self-adhesive resin cement after aqueous aging. Materials and Methods: Disc-shaped specimens of 3 conventional (C1: Multilink N, C2: Duolink, C3: Nexus 3) and 3 self-adhesive (S1: Multilink Speed, S2: Biscem, S3: Maxcem) types of resin cements were subjected to irradiation. After 24 h, the Knoop microhardness of each resin cement was evaluated. The specimens were immersed separately in distilled water and maintained at 37 degrees C. A total of 5 specimens of each resin cement were collected at the following time intervals of immersion: 1, 6, 12 and 18 months. The samples were used to evaluate the Knoop parameters of microhardness, sorption and solubility. The surface morphology of the specimens after 18 months of immersion was observed by scanning electron microscopy. The sorption and solubility data were analyzed by two-way ANOVA. The Knoop microhardness was tested by the ANOVA repeated measures (P<0.05). Results: The sorption and solubility parameters of C1 and S1 exhibited significant fluctuations during the aqueous aging. The hardness of the S1 and S2 specimens decreased significantly after an 18-month water immersion. The Si, S2 and S3 specimens indicated higher filler exposure and stripping and apparent pores and cracks compared to specimens C1, C2 and C3, respectively. Conclusion: The surface of selfadhesive resin cements is more susceptible to aqueous damage than that of the conventional resin cements.
Increasing Acid Concentration, Time and Using a Two-Part Silane Potentiates Bond Strength of Lithium Disilicate–Reinforced Glass Ceramic to Resin Composite: An Exploratory Laboratory Study

Matilde Almiro,Beatriz Marinho,António H. S. Delgado,João Rua,Paulo Monteiro,Inês Caetano Santos,Luís Proença,José João Mendes,Marco M. M. Gresnigt

DOI: https://doi.org/10.3390/ma15062045

IF: 3.4

2022-03-10

Materials

Abstract:There is still a lack of consensus concerning the recommended etching concentration, application time and type of silane when bonding lithium disilicate-reinforced glass ceramics manufactured by CAD/CAM. The purpose of this study was thus to conduct an in vitro study which investigates the influence of hydrofluoric acid (HF) concentration, etching time and silane type on the microtensile bond strength (μTBS) of lithium disilicate to resin composites. Thirty-nine IPS e.max CAD blocks were randomly divided between thirteen groups (n = 3). The variables were HF concentration (9.5 or 4.9%), etching time (20 or 60 s) and silane type (Bis-Silane, Monobond Plus and ESPE Sil Silane). The blocks were cut into beams, aged for 10,000 cycles in a thermocycler and submitted to tensile stress to determine μTBS. A control group featuring the Monobond Etch & Prime (MEP) agent that combines etching/silanisation into a simultaneous process was also added. This group was discarded from the analysis due to only having pre-test failures. The data were analysed using a three-way ANOVA (α = 0.05). The HF concentration, etching time and silane type significantly influenced μTBS (p < 0.001). Significant interactions between time and silane type (p = 0.004), HF concentration and silane type (p < 0.001) and among the three factors (p < 0.001) were noted. Etching lithium disilicate with 9.5% HF (60 s), followed by the application of Bis-Silane, resulted in the highest μTBS (16.6 ± 9.0 MPa). The highest concentration and etching time under study, combined with a two-part silane, resulted in the highest bond strength, while the application of MEP showed a complete pre-test failure.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,metallurgy & metallurgical engineering
Bond strength of three luting agents to zirconia ceramic - influence of surface treatment and thermocycling

Ahmed Attia

DOI: https://doi.org/10.1590/s1678-77572011005000015

Abstract:Objective: This in vitro study aimed to evaluate the influence of different surface treatments, 3 luting agents and thermocycling on microtensile bond strength (µTBS) to zirconia ceramic. Material and methods: A total of 18 blocks (5x5x4 mm) were fabricated from zirconia ceramic (ICE Zirkonia) and duplicated into composite blocks (Alphadent). Ceramic blocks were divided into 3 groups (n=6) according to the following surface treatments: airborne-particle abrasion (AA), silica-coating, (SC) (CoJet) and silica coating followed by silane application (SCSI) (ESPE Sil). Each group was divided into 3 subgroups (n=2) according to the 3 luting agents used. Resin-modified glass-ionomer cement (RMGIC, Ketac Cem Plus), self-adhesive resin cement (UN, RelyX Unicem) and adhesive resin cement (ML, MultiLink Automix) were used for bonding composite and zirconia blocks. Each bonding assembly was cut into microbars (10 mm long and 1±0.1 mm²). Seven specimens of each subgroup were stored in water bath at 37ºC for 1 week. The other 7 specimens were stored in water bath at 37ºC for 30 days then thermocycled (TC) for 7,500 cycles. µTBS values were recorded for each specimen using a universal testing machine. Statistical analyses were performed using a 3-way ANOVA model followed by serial 1-way ANOVAs. Comparison of means was performed with Tukey's HSD test at (α=0.05). Results: µTBS ranged from 16.8 to 31.8 MPa after 1 week and from 7.3 to 16.4 MPa after 30 days of storage in water and thermocycling. Artificial aging significantly decreased µTBS (p<0.05). Considering surface treatment, SCSI significantly increased µTBS (p<0.05) compared to SC and AA. Resin cements (UN and ML) demonstrated significantly higher µTBS (p<0.05) compared to RMGIC cement. Conclusions: Silica coating followed by silane application together with adhesive resin cements significantly increased µTBS, while thermocycling significantly decreased µTBS.
Optimal Hydrofluoric Acid Etching Duration and Impact of Silane/Adhesive on Profilometric Properties and Bonding to Lithium Disilicate Glass Ceramics

T S Porto,A J Faddoul,S J Park,V P Feitosa,T F Eyüboğlu,M Ozcan

DOI: https://doi.org/10.2341/24-015-L

2024-09-01

Abstract:Objectives: This study aimed to assess the surface roughness, surface free energy (SFE), and shear bond strength (SBS) on a lithium disilicate glass-ceramic surface following varying etching protocols (time variation) and application of silane either with or without adhesive material. Methods and materials: Lithium disilicate glassceramic (LDGC) computer-aided design and computer-aided manufacture (CAD/CAM) blocks were cut using a slow-speed cutting mechanism. CAD/CAM blocks were then evaluated for surface roughness, 6 groups (n=20); SFE,12 groups (n=5); and SBS, 10 groups (n=10). The cut CAD/CAM blocks were randomly allocated to 28 groups. Groups were based on the following: 30 or 90 seconds of etching with 9% hydrofluoric acid (HF); application or absence of silane coupling agent (Sil); and application or absence of adhesive (Adh).The control group (Cont) had untreated surfaces. Unetched surfaces were surveyed with only silane (Sil), only adhesive (Adh), or silane+adhesive (SilAdh). Further etched groups were HF30 with HF for 30 seconds, HF30-Sil, HF30-Adh, and HF30-SilAdh. Alternative 90-second etching times produced similar groups: HF90, HF90-Sil, HF90-Adh, and HF90-SilAdh. A digital profilometer was used to assess the surface roughness of specimens, and two readings were recorded. Sessile drop analysis was used to examine SFE specimens, and the OWRK model was modified to measure liquid surface tension. A universal testing machine (UltraTester, Ultradent Products, Inc, South Jordan, UT, USA) was utilized for the SBS test, with the crosshead speed set at 0.5 mm/min until failure. Representative treated specimens from each group were submitted to surface morphological evaluation and chemical analysis using scanning electron microscopy/energy dispersive x-ray spectroscopy (SEM/EDXS) (n=3). After data collection, evaluation using one- or two-way analysis of variance and the post-hoc Tukey test (α=5%) was conducted. Results: A longer etching time of 90 seconds produced a rougher surface. After the 90-second etching process, SFE displayed the greatest values; nevertheless, the use of silane did not affect SFE. For every group examined, the application of silane followed by adhesive resulted in an increase in SBS and more stable bonding over time. SEM/EDXS showed that etching times did affect the amount of cerium on the surface and altered surface morphology. Conclusions: Higher and more consistent bond strengths have been observed with longer etching periods. Silane and adhesive application on the ceramic surface showed stronger and enhanced bond strength, specifically when longer etching times were employed.
Bond Strength between Different Zirconia-Based Ceramics and Resin Cement before and after Aging

Marcos Paulo Motta Silveira,Nathália de Carvalho Ramos,Guilherme da Rocha Scalzer Lopes,João Paulo Mendes Tribst,Marco Antonio Bottino

DOI: https://doi.org/10.3390/coatings12101601

IF: 3.236

2022-10-22

Coatings

Abstract:The objective of this study was to evaluate the bond strength of different stabilized zirconias with resin cement and evaluate the susceptibility to thermal aging of the adhesive interface. Zirconia discs (Vita Zahnfabrik, Bad Säckingen, Germany) were obtained: 3Y-TZP first generation (translucent), 3Y-TZP third generation (high-translucent), 4Y-PSZ (super-translucent), and 5Y-PSZ (extra-translucent). Each disc had its surface polished with a standardized protocol. The specimens were cleaned and sintered according to the manufacturer's recommendation (conventionally: ~12 h). However, 3Y-TZP groups were subdivided into subgroups and sintered following the speed sintering process (~80 min). After their sintering shrinkage, the dimensions of the final discs were 12 mm × 2 mm. The specimens were blasted with 50 μm aluminum oxide (1 cm distance, 2 bar pressure, and 2 s/cm2), cleaned, and silanized with an MDP primer. After the surface treatment, a resin cement cylinder was built on the ceramic surface (Ø = 1 mm; h = 2 mm). Half of the specimens of each group were subjected to a microshear bond strength test in a universal testing machine after 24 h of cementation, while the other half were subjected to thermocycling prior to the bond strength test (6000 cycles; 5 °C–55 °C, 30 s for each bath). Bond strength data were submitted to two-way ANOVA and Tukey's test (95%), as well as Weibull analysis, to determine adhesive reliability. Bond strength was statistically different among the materials, and only 3Y-TZP third generation and 4Y-PSZ were not affected by thermal aging. The speed sintering method was statistically similar to the conventional process for 3Y-TZP first generation. However, 3Y-TZP third generation showed higher immediate bond strength when speed sintered. The Weibull modulus was superior for conventional 3Y-TZP third generation and 4Y-PSZ. In this study, thermal aging caused a degradation of the adhesive interfaces of 3Y-TZP first generation and 5Y-PSZ with the resin cement; however, it did not affect the interfaces of 3Y-TZP third generation and 4Y-PSZ. The speed sintering method did not affect the long-term bond strength with the resin cement. Adhesive reliability was superior for 3Y-TZP third generation and 4Y-PSZ.

materials science, multidisciplinary,physics, applied, coatings & films
Effect of hydrofluoric acid and self-etch ceramic primers on the flexural strength and fatigue resistance of glass ceramics: A systematic review and meta-analysis of in vitro studies

Paulo Matias Moreira,Gabriela Luiza Moreira Carvalho,Rodrigo de Castro Albuquerque,Carolina Bosso André

DOI: https://doi.org/10.1016/j.jdsr.2024.06.001

IF: 6.468

2024-06-26

Japanese Dental Science Review

Abstract:This systematic review evaluated the effect of different hydrofluoric acid (HF) etching regimens and a self-etch ceramic primer (SECP) on the flexural strength (FS) and fatigue failure load (FFL) of glass-ceramic materials.The identification of relevant studies was conducted by two authors in five databases: PubMED, Scopus, Web Of Science, LILACS and Virtual Health Library (BVS) until July 2022 with no year limit. The analysis was conducted in RevMan 5.4.1 Software (Cochrane Collaboration) using Random effect model at 5 %. The risk of bias of the included studies were assessed. From the 5349 articles identified, 34 were included for quantitative analysis. Meta-analysis showed that for predominantly glassy ceramics, etching with HF 5 % had no significant impact on FS, however, HF acid etching with concentrations greater than 5 % negatively impacted FS. For lithium disilicate glass-ceramics (LDGC) HF acid etching, negatively influenced FS, while increasing the FFL. HF etching negatively affected FS of hybrid ceramics. The self-etch ceramic primer and HF acid etching showed a similar impact on FFL and FS. This meta-analysis indicates that the impact of SECP and HF acid etching on the mechanical behavior of glass ceramics is material-dependent.

dentistry, oral surgery & medicine
Long-term effect of firing protocols on surface roughness and flexural strength of lithium disilicate glass-ceramic

Kaíssa da Cunha Lima,Rocio Geng Vivanco,Pedro Roberto Braz Rodrigues,Ana Lúcia Pereira Caetano,Fernanda de Carvalho Panzeri Pires-de-Souza

DOI: https://doi.org/10.1590/0103-6440202305496

2023-10-01

Brazilian Dental Journal

Abstract:Abstract This study evaluated the effect of different firing protocols on the surface roughness and flexural strength of CAD/CAM lithium disilicate glass-ceramic (LD) after aging methods. Forty-two LD bars of 16 x 4 x 2 mm (IPS e-max CAD, Ivoclar) were randomly separated into two groups according to firing protocols: Single firing-Staining, glazing, and crystallization in a single step; Multiple firings-Crystallization+First staining+Firing+Second staining+Firing+Glazing+Firing. After protocols, initial surface roughness readings were taken (Surfcorder SE1700, Kosakalab). Samples were then randomly separated into three groups (n=7) according to the aging methods they were submitted: Thermomechanical cycling (TMC, ER System, Erios, 1,200,000 cycles, 0.3 MPa, 2 Hz and 5°C/37°C/55°C, 30 s swell time); Simulated toothbrushing (STB, Pepsodent, MAVTEC, 73,000 cycles), and Control (no aging). Final surface roughness readings were done, and samples were submitted to a three-point bending test (OM100, Odeme Dental Research) and fractographic analysis by scanning electron microscopy (EVO-MA10, ZEISS). Data were analyzed (2-way ANOVA, (α=.05). There was no difference (p>.05) in the flexural strength between the firing protocols, regardless of the aging method. STB decreased the flexural strength of samples submitted to multiple firings, different from control (p<.05). Without aging (Control), before TMC, and after STB, LD had lower surface roughness when submitted to multiple firings than to single firing (p<.05). The firing protocols did not affect the flexural strength or the surface roughness of the lithium disilicate glass-ceramic, even after aging. However, toothbrushing negatively affected the flexural strength and smoothed the surface of the ceramic submitted to multiple firings.
Comparative Invitro Testing of the Tensile Bond Strength Under Artificial Aging Between Different Lithium Disilicate Ceramics to Composite Substrate: A Novel Methodology

Osamah A Alsulimani,Abdulrahaman J Alhaddad,Arwa U AlSaggaf,Mosa Altassan,Mazen Alghamdi,Samar H Abuzinadah,Maher S Hajjaj,Amin A Marghalani

DOI: https://doi.org/10.7759/cureus.66163

2024-08-05

Cureus

Abstract:Objective The purpose of this study is to compare the tensile bond strength values to composite substrate pre- and post-aging between IPS E.max CAD and Initial LiSi. Methods The study utilized four blocks of IPS E.max CAD LT/B1 C14 (Ivoclar Vivadent, Liechtenstein, Germany) (referred to as E) and four blocks of Initial LiSi LT/B1 (GC, Tokyo, Japan) (referred to as L). These blocks were milled to produce 76 ceramic bars measuring 2 mm × 2 mm × 10 mm (E = 38, L = 38/n = 19). After acid etching with hydrofluoric acid (BISCO, Schaumburg, IL, USA) and silane application (BIS-SILANE, BISCO), the specimens were embedded in putty (Express STD, 3M, Decatur, AL, USA) to create a mold for the resin cement (RelyX U200, 3M). Subsequently, one group of each brand underwent mechanical tensile testing (E0 and L0), while the other groups were subject to tensile testing after artificial aging involving 500 thermal cycles between 5 and 55°C (E5 and L5). The mean tensile strength for each group (E0, E5, L0, and L5) was determined using the Brown-Forsythe one-way ANOVA and Tamhane's post hoc tests. Results Initial LiSi showed a superior pre-aging mean (11.7 MPa). However, both materials had identical post-aging means (7.6 MPa). There were no statistically significant differences, except between the dependent Initial LiSi groups (L0-L5). Most failure modes were mixed (cohesive cement and adhesive). There were no cohesive failures on the cement side except in three specimens of Initial LiSi post-aging. Conclusion The tested conditions have shown that Initial Lisi exhibited the highest pre-aging mean; however, it exhibited inferior bond stability under aging conditions compared to IPS E.max CAD. Analyzing the microstructure before and after aging may provide insights into the greater decrease in bond strength observed in the Initial LiSi specimens.

Vitamin E status and metabolism in adult and aged aryl hydrocarbon receptor null mice.

Adhesion to lithium disilicate glass-ceramics after aging: Resin viscosity and ceramic surface treatment effects

The Influence of Hydrofluoric Acid Temperature and Application Technique on Ceramic Surface Texture and Shear Bond Strength of an Adhesive Cement

Effect of Hydrofluoric Acid Etching Time on the Resin Bond Durability of Glass Ceramic

Effect of Etching Time and Resin Bond on the Flexural Strength of IPS E.max Press Glass Ceramic.

Effect of Hydrothermal Aging on the Flexural Strength and Microhardness of Materials Used for Additive or Subtractive Manufacturing of Definitive Restorations

[Effect of Hydrofluoric Acid Etching Time and Resin Bonding on the Flexural Strength of Lithium Disilicate Glass Ceramic].

[Effect of Hydrofluoric Acid Concentration on the Surface Morphology and Bonding Effectiveness of Lithium Disilicate Glass Ceramics to Resin Composites].

Fatigue failure load of zirconia-reinforced lithium silicate glass ceramic cemented to a dentin analogue: Effect of etching time and hydrofluoric acid concentration

Recycling CAD/CAM Lithium Disilicate Ceramic: Effect of Surface Treatment and Aging on the Bond Strength to Resin Cement

Effect of Resin Cement Viscosities and Surface Roughness on Shear Bond Strength of Conditioned Polymer Infiltrated Ceramic Network

Biaxial flexural strength of hydrothermally aged resin-based materials

Bond Strength to Lithium-Disilicate Ceramic after Different Surface Cleaning Approaches

Surface morphology and mechanical properties of conventional and self-adhesive resin cements after aqueous aging.

Increasing Acid Concentration, Time and Using a Two-Part Silane Potentiates Bond Strength of Lithium Disilicate–Reinforced Glass Ceramic to Resin Composite: An Exploratory Laboratory Study

Bond strength of three luting agents to zirconia ceramic - influence of surface treatment and thermocycling

Optimal Hydrofluoric Acid Etching Duration and Impact of Silane/Adhesive on Profilometric Properties and Bonding to Lithium Disilicate Glass Ceramics

Bond Strength between Different Zirconia-Based Ceramics and Resin Cement before and after Aging

Effect of hydrofluoric acid and self-etch ceramic primers on the flexural strength and fatigue resistance of glass ceramics: A systematic review and meta-analysis of in vitro studies

Long-term effect of firing protocols on surface roughness and flexural strength of lithium disilicate glass-ceramic

Comparative Invitro Testing of the Tensile Bond Strength Under Artificial Aging Between Different Lithium Disilicate Ceramics to Composite Substrate: A Novel Methodology