Abstract:M-series molecules are one kind of promising acceptor-donor-acceptor (A-D-A)-type acceptors for constructing high-performance organic solar cells (OSCs). However, their power conversion efficiencies (PCEs) are lagging behind that of current state-of-the-art OSCs, limited by the relatively low fill factor (FF) and photocurrent. Herein, combined strategies of layer-by-layer (LBL) deposition and interface engineering are conducted to systematically improve light utilization and thus PCEs for M36-based OSCs. Through choosing a proper processing solvent, a PCE of 17.3% with an FF of 77.9% is achieved for the resulting LBL devices, much higher than those (15.9%/74.0%) from the blend-casting devices. The improvement is assigned to the favorable morphological evolution that facilitates carrier generation and transport as well as reduces charge recombination. More importantly, light-harvesting of the active layers can be enhanced upon employing a self-assembled monolayer of (2-(9H-carbazol-9-yl)ethyl)phosphonic acid (2PACz) instead of the widely used PEDOT:PSS as the hole-selecting layer, due to the decreased parasitic absorption of the former. Consequently, 2PACz-based LBL devices exhibit significantly increased photocurrent, affording a PCE up to 18.2%, which is the highest among the reported A-D-A-type acceptor-based OSCs. These results deliver important strategies to enhance the performance of OSCs and thus highlight the great potential of M-series acceptors for practical applications. The issue of low fill factor for M-series acceptor-based organic solar cells (OSCs) has been addressed by delicate morphology control with the layer-by-layer deposition. Meanwhile, increased photocurrent has been achieved by a self-assembled monolayer (2PACz)-based interface engineering for light management within devices. The combined strategies lead to a promising power conversion efficiency of over 18% for the M-series acceptor-based OSCs. image

Layer‐by‐Layer Processed Organic Solar Cells with 18.02% Efficiency Enabled by Regulating the Aggregation of Bottom Polymers

Layer-by-Layer-Processed All-Polymer Solar Cells with Enhanced Performance Enabled by Regulating the Microstructure of Upper Layer

Optimization of Active Layer Morphology for High-Efficiency Layer-by-Layer Organic Solar Cells with 18.13% Efficiency

Hierarchical Solid‐Additive Strategy for Achieving Layer‐by‐Layer Organic Solar Cells with Over 19% Efficiency

Layer‐by‐Layer Organic Solar Cells Enabled by 1, 2, 4‐Selenadiazole‐Containing Crystalline Small Molecule with Double‐Fibril Network Morphology

Additive-Induced Vertical Component Distribution Enables High-Performance Sequentially Cast Organic Solar Cells.

Layer‐by‐Layer All‐Polymer Solar Cells Approaching 19% with Dual‐Donor Modulation of an Interpenetrating Network

Layer‐by‐Layer Solution Processing Method for Organic Solar Cells

Controlling Vertical Phase Separation and Crystallization via Solvent Synergy Strategy to Empower Layer-by-Layer Processed Organic Solar Cells

19.10% Efficiency and 80.5% Fill Factor Layer‐by‐Layer Organic Solar Cells Realized by 4‐Bis(2‐thienyl)pyrrole‐2,5‐Dione Based Polymer Additives for Inducing Vertical Segregation Morphology

Optimized Active Layer Morphology Toward Efficient and Polymer Batch Insensitive Organic Solar Cells

A Layer-by-Layer Architecture for Printable Organic Solar Cells Overcoming the Scaling Lag of Module Efficiency

Achieving 20.8% Organic Solar Cells Via Additive-Assisted Layer-by-layer Fabrication with Bulk P-I-n Structure and Improved Optical Management

Solid Additive-Assisted Layer-by-Layer Processing for 19% Efficiency Binary Organic Solar Cells

Polymer Solar Cells with 18.74% Efficiency: From Bulk Heterojunction to Interdigitated Bulk Heterojunction

High-Performance Layer-by-Layer Organic Solar Cells Enabled by Non-Halogenated Solvent with 17.89% Efficiency

Realizing over 18% Efficiency for M-Series Acceptor-Based Polymer Solar Cells by Improving Light Utilization

High‐Efficiency Sequential‐Cast Organic Solar Cells Enabled by Dual Solvent‐Controlled Polymer Aggregation

Layer-by-layer slot-die coated high-efficiency organic solar cells processed using twin boiling point solvents under ambient condition

High Efficiency Layer‐by‐Layer All‐Polymer Solar Cell Enabled by Bottom‐Layer Optimization

High‐Performance Large‐Area Organic Solar Cells Enabled by Sequential Bilayer Processing via Nonhalogenated Solvents