Abstract:Recently, the polymer solar cells (PSCs) based on the PM6 and small molecular acceptor (SMA) Y6 have attracted considerable attention in this community for their outstanding photovoltaic performance. As well known, the molecular weight of polymer has dramatic impact on the blend morphology and photovoltaic performance in the polymer solar cells, especially for those polymers with temperature‐dependent aggregation (TDA) behavior. In this work, a series of PM6 polymers with different weight‐average molecular weights (Mw= 41, 67, 74, 84 and 114 kDa) were synthesized, and the effects of the Mw on the morphology and photovoltaic performance were systematically investigated. Notably, tuning the molecular weight induces dramatic influences on the aggregation behaviors of the polymers and their corresponding blend morphology, which were explored by the temperature‐dependent UV‐vis absorptions (TD‐Abs), grazing incidence wide‐angle X‐ray scattering (GIWAXS) and resonant soft X‐ray scattering(R‐SoXS) measurements. Increasing Mw promoted the strong face‐on molecular packing and reduced the blend film domain sizes for enhanced donor‐acceptor interfacial areas, resulting in increased short‐circuit current densities (Jsc) and fill factor (FF). However, polymer donor with high Mw value processed stronger tendency of forming excessive pure donor aggregate, which hampered forming the intermixed phase for efficient charge transport, resulting in the inferior FF. Therefore, the optimized OSCs based on PM6 with moderate molecular weight (Mw=74 kDa) and Y6 exhibited suitable size and purity of the domains, facilitating well‐balanced charge transport, reducing trap‐assisted recombination and leading to significant enhancement of photovoltaic performance with the optimal PCE of 17.1%. This work indicates that proper and precisely tuning the molecular weight of polymer donor is critical to enhance the photovoltaic performance in PSCs.This article is protected by copyright. All rights reserved.

Constructing Multiscale Fibrous Morphology to Achieve 20% Efficiency Organic Solar Cells by Mixing High and Low Molecular Weight D18

Layer‐by‐Layer Processed Organic Solar Cells with 18.02% Efficiency Enabled by Regulating the Aggregation of Bottom Polymers

Synergistic Control of Multilength-Scale Morphology and Vertical Phase Separation for High-Efficiency Organic Solar Cells

2D/1a Strategy to Regulate Film Morphology for Efficient and Stable Nonfullerene Organic Solar Cells

Thickness Insensitive Organic Solar Cells with High Figure‐of‐Merit‐X Enabled by Simultaneous D/A Interpenetration and Stratification

Revealing Morphology Evolution in Highly Efficient Bulk Heterojunction and Pseudo‐Planar Heterojunction Solar Cells by Additives Treatment

Achieving 19.78%‐Efficiency Organic Solar Cells by 2D/1A Ternary Blend Strategy with Reduced Non‐Radiative Energy Loss

19.10% Efficiency and 80.5% Fill Factor Layer‐by‐Layer Organic Solar Cells Realized by 4‐Bis(2‐thienyl)pyrrole‐2,5‐Dione Based Polymer Additives for Inducing Vertical Segregation Morphology

Correlating Electronic Structure and Device Physics with Mixing Region Morphology in High‐Efficiency Organic Solar Cells

Morphology Optimization via Pre-aggregation and Miscibility Matching in PM6:L8-BO Ternary Organic Solar Cells

Morphology Optimization by Non‐Halogenated and Twisted Volatile Solid Additive for High‐Efficiency Organic Solar Cells

Synergistic Effect of Solvent and Solid Additives on Morphology Optimization for High-Performance Organic Solar Cells

Tuning Aggregation Behavior of Polymer Donor via Molecular‐Weight Control for Achieving 17.1% Efficiency Inverted Polymer Solar Cells

Oligothiophene Additive‐Assisted Morphology Control and Recombination Suppression Enable High‐Performance Organic Solar Cells

High‐Efficiency (16.93%) Pseudo‐Planar Heterojunction Organic Solar Cells Enabled by Binary Additives Strategy

Enabling High‐Efficiency and Stable Binary Organic Solar Cells by Solid Additive‐Assisted Morphology Modulation

Fibrillization of Non‐Fullerene Acceptors Enables 19% Efficiency Pseudo‐Bulk Heterojunction Organic Solar Cells

Dual-Additive-Driven Morphology Optimization for Solvent-Annealing-Free All-Small-Molecule Organic Solar Cells

Achieving 20.8% Organic Solar Cells Via Additive-Assisted Layer-by-layer Fabrication with Bulk P-I-n Structure and Improved Optical Management

Miscibility Control by Tuning Electrostatic Interactions in Bulk Heterojunction for Efficient Organic Solar Cells

Rationally Tuning Blend Miscibility of Polymer Donor and Nonfullerene Acceptor for Constructing Efficient Organic Solar Cells<sup>※</sup>