Abstract:New technologies in polymer synthesis and pipe extrusion equipment have led to the commercialization of high-performance, large-diameter, thick-wall high density polyethylene (HDPE) pipes. They have been used in the field of seawater transport and cooling to replace metal pipes, due to their advantages of high corrosion resistance and extensibility. Connection of HDPE pipe is important as it determines the safety of the entire piping system. Butt fusion welding is commonly used for HDPE pipe connection but may cause the formation of weak points in the welded joints, interfering the reliability of the pipeline system in the application of nuclear power plants. At present, there is a lack of research on evaluating the performance of welded joint for large-diameter thick-wall HDPE pipes made by butt fusion-welding. The purpose of this study is to investigate the influence of three different butt fusion-welding processes, i.e., single low pressure (SLP), single high pressure (SHP) and dual low pressure (DLP), by evaluating the performance of their welded joints, including characterizing tensile strength, extensibility, crystallinity and hardness. In specific, a thick-wall HDPE pipe with OD of 812.8mm and wall thickness of 74mm which is certified for nuclear safety class was used for study. Representative specimen from the outer, middle and inner part across the wall of the main pipe body and welded joints were taken for testing. Different test methods and specimens were designed to assess the feasibility of evaluating the welding performance from different welding process. The results showed that the mechanical properties of different locations of the welded joints were different, and the tensile strength and fracture energy of the middle part of the joint were lower than that of the inner and outer parts, which could be caused by the difference in the crystallinity and thickness of the melting zone influenced by welding processes, as can be seen from the analysis of DSC test and morphology observation. Hardness testing was conducted on the section of the welded joints, and it revealed that the micromechanical properties of the welded joints in the region of the heat-affected zone were enhanced significantly, which may be due to the annealing effect caused by welding process. In summary, The DLP process resulted in the best extensibility of the welded joints among three processes, suggesting that the joining pressure from welding process plays an important role in affecting the extensibility of the welded joints.

Investigation on the hot melting temperature field simulation of HDPE water supply pipeline in gymnasium pool

Simulation of Temperature Field in HDPE Pipe Thermal Welding

Ultrasonic Technique For Testing Cold Welding Of Butt-Fusion Joints In Polyethylene Pipe

Test Research on Water Resistant Performance of Hot Melt Adhesive in Plastic Pipe Reinforced by Cross-winding Steel Wires

Research on Phased Array Ultrasonic Technique for Testing Butt Fusion Joint in Polyethylene Pipe

Investigation on the Allowable Temperature During Electrofusion Welding of Polyethylene Pipe

Analysis on Temperature Field in Electrofusion Joint for Polyethylene Pipes

Study on the Allowable Temperature for Preventing Over Welding During Thermal Welding of Polyethylene Pipe

Welding Residual Stress in HDPE Pipes: Measurement and Numerical Simulation

A Model for Predicting Temperature of Electrofusion Joints for Polyethylene Pipes

Experimental study on microwave test of cold weld defects in HDPE piping thermal fusion welds

Comparative study on the performance of butt fusion-welding processes for nuclear safety class large-diameter thick-walled PE pipes

An experimental‐based thermal prediction model for butt fusion welding of polymer pipes

Applicability Analysis of Thermoplastic Material As Liner Pipe for Trenchless Rehabilitation of Thermal Pipelines

Detecting Cold Weld Defects in HDPE Piping Thermal Fusion Welds Based on Microwave Technique

Thermal, metallurgical and mechanical analysis of circumferentially multi-pass welded P92 steel pipes

Ultrasonic Inspection of Welding in Electro-Fusion Joint of Polyethylene Pipes

Investigating the Deformation Characteristics of Buried High-Density Polyethylene Pipes: Considering the Effect of Sequentially Applying Pressure and Elevating Temperature

Modeling of Temperature Field and Pool Formation During Linear Laser Welding of DP1000 Steel

Effect Simulation of Fire Damage to Thermal Performance of High Density Polyethylene Pipe

Demonstration of Intelligent Welding Machine for Polyethylene Pipe