Abstract:Recent advancements in printable mesoscopic perovskite solar cells (p‐MPSCs) face challenges in improving perovskite precursor solution diffusion during assembly. The research achieves effective gap‐driven diffusion, forming well‐filled perovskite through TiO2 nanorod arrays. The bilayer electron transport layer with dual crystal phase and cascaded energy levels demonstrates superior electron collection and directional transport. Suppression of nonradiative recombination and efficient charge transfer lead to notable enhancements in open‐circuit voltage and short‐circuit current density. Consequently, p‐MPSCs' power conversion efficiency increases from 14.32% to 16.07%, close to literature's highest reported value of 16.21%. These results highlight a novel interface engineering approach for high‐performance p‐MPSCs fabrication. Recently, enhancing the photovoltaic performance of printable mesoscopic perovskite solar cells (p‐MPSCs) poses a significant challenge, particularly in improving the diffusion of perovskite precursor solutions during device assembly. In this research, effective gap‐driven diffusion of the precursor solution perovskite is successfully achieved, leading to the formation of well‐filled and crystallized perovskite through TiO2 nanorod arrays. By incorporating upper‐layer TiO2 nanoparticles, a bilayer electron transport layer with dual crystal phase is developed, establishing a cascaded energy level structure that exhibits superior capabilities in electron collection and directional transport. The effective suppression of nonradiative recombination and efficient charge transfer result in notable enhancements in both open‐circuit voltage and short‐circuit current density. Consequently, the power conversion efficiency of p‐MPSCs devices based on MAPbI3 γ‐butyrolactone solution increases from 14.32% to 16.07% (highest reported value in the literature is 16.21%). These findings highlight a novel interface engineering approach for the fabrication of high‐performance p‐MPSCs devices.

Improving Hole‐Conductor‐Free Fully Printable Mesoscopic Perovskite Solar Cells’ Performance with Enhanced Open‐Circuit Voltage via the Octyltrimethylammonium Chloride Additive

Efficient Carbon‐Based Hole‐Conductor‐Free Printable Mesoscopic Perovskite Solar Cells via a Multifunctional Fluorinated Molecule

Enhancing the Photovoltaic Performance of Printable Mesoscopic Perovskite Solar Cells Via 5-Amino-4-formylimidazole Hydrochloride

Band Alignment Strategy for Printable Triple Mesoscopic Perovskite Solar Cells with Enhanced Photovoltage

Stratified Oxygen Vacancies Enhance the Performance of Mesoporous TiO2 Electron Transport Layer in Printable Perovskite Solar Cells

Minimizing the Voltage Loss in Hole‐Conductor‐Free Printable Mesoscopic Perovskite Solar Cells

Efficient Bifacial Passivation Enables Printable Mesoscopic Perovskite Solar Cells with Improved Photovoltage and Fill Factor

Electron injection and defect passivation for high-efficiency mesoporous perovskite solar cells

A Polymer Defect Passivator for Efficient Holeâ€�Conductorâ€�Free Printable Mesoscopic Perovskite Solar Cells

Two Birds with One Stone: Defect Passivation and Energy Level Optimization Achieved by Using Ionic Liquid Additives for Printable Mesoscopic Perovskite Solar Cells with Efficiency beyond 16%

Nanoscale Pumping Effect of Perovskite via Supported Bilayer Electron Transport Layer for Efficient Printable Mesoscopic Solar Cells

Surface Lattice Perturbation of Electron Transport Layer Reducing Oxygen Vacancies for Positive Photovoltaic Effect

Minimizing Voltage Losses via Synergistically Reducing Hetero-Interface Energy Offset for High Efficiency Perovskite Solar Cells

In Situ Reconstruction Post‐Treatment for Efficient Carbon‐Based Hole‐Conductor‐Free Printable Mesoscopic Perovskite Solar Cells

Improvements in Printable Mesoscopic Perovskite Solar Cells Via Thinner Spacer Layers

Enhanced photovoltaic performance and reduced hysteresis in hole-conductor-free, printable mesoscopic perovskite solar cells based on melamine hydroiodide modified MAPbI3

Improved Pore-Filling and Passivation of Defects in Hole-Conductor-Free, Fully Printable Mesoscopic Perovskite Solar Cells Based on D-Sorbitol Hexaacetate-Modified MAPbI3

The Surface Effect of Chlorinated Mesoscopic TiO2 in Printable Carbon-Based Perovskite Solar Cells

Tailoring the Dimensionality of Hybrid Perovskites in Mesoporous Carbon Electrodes for Type‐II Band Alignment and Enhanced Performance of Printable Hole‐Conductor‐Free Perovskite Solar Cells

Oxygen Management in Carbon Electrode for High-Performance Printable Perovskite Solar Cells

Mesoporous TiO 2 Electron Transport Materials Derived from 2D Ti-MOFs for Enhanced Power Conversion Efficiency in Printed Mesoscopic Perovskite Solar Cells