Abstract:HA composite coatings added reinforcement phases could improve the mechanical properties and bonding strength of the coatings. Cold spraying is a feasible surface technology for preparing HA composite coatings. In order to investigate the influence of cold spraying parameters on the deposition behavior of a single HA/Ti composite particle, numerical and experimental investigation of gas-particle two-phase flow in cold spraying nanostructured HA/Ti composite particle were investigated in this study. The results show that the influence of different temperatures and pressures on static pressure was not significant. The effects of gas pressure on the static temperature were tiny under the same inlet temperature and different pressure conditions; however, the static temperature in the entire spray gun cavity increased as the inlet temperature increased under the same pressure and different inlet temperature conditions. There is little effect of gas pressure on the axial velocity of gas flow in the spray gun cavity; however, the axial velocity of gas flow increased with the increase in gas temperature. Meanwhile, the axial velocity of gas flow gradually increases throughout the spraying process. At a gas temperature of 573 K and 973 K, the maximum axial velocities of a gas flow at gas pressure of 2.2 MPa were 778 m/s and 942 m/s, respectively. There is little effect of gas pressure on the axial velocity of HA/30 wt.% Ti particles under the same gas temperature. The axial velocity of HA/30 wt.% Ti particles increased with the increase in gas temperature under the same gas pressure condition. The axial velocity of composite particles decreased with the increase in the particle size under the same gas pressure and gas temperature. At a gas temperature of 573 K and 973 K, the minimum axial velocity of HA/30 wt.% Ti particles with a particle size of 30 μm at a gas pressure of 2.2 MPa was 435 m/s and 467 m/s, respectively. A certain deformation of splats occurred after impacting the substrate, and the splats adhered to the surface of the Ti6Al4Vsubstrate, clearly presenting a flat shape with a central hump surrounded by a ringy band. At a gas temperature of 973 K, particles generated more severe deformation with more cracks and ejecta phenomenon. The splats attached to the substrate were increased as the gas temperature increased.

In-flight aggregation and deposition behaviour of particles in low pressure cold spray

Experimental and Modeling Investigation of Liquid-Induced Agglomeration in a Gas–Solid Fluidized Bed with Liquid Spray

Evolution and Fluidization Behaviors of Wet Agglomerates Based on Formation-Fragmentation Competition Mechanism

Research Progress on Numerical Simulation of the Deposition and Deformation Behavior of Cold Spray Particles

Effects of operating conditions on droplet deposition onto surface of atomization impinging spray

Modeling of Micro- and Nanoparticle Characteristics in DC Suspension Plasma Spray

Effects of Atomization Injection on Nanoparticle Processing in Suspension Plasma Spray

Experimental study on microscopic characteristics of impinging spray at elevated ambient pressure conditions during development

Dynamic Modeling of Micro- and Nano-Sized Particles Impinging on the Substrate During Suspension Plasma Spraying

Formation conditions of vortex-like intermixing interfaces in cold spray

Relationship between deposition properties and operating parameters for droplet onto surface in the atomization impinging spray

Study of Low-Pressure Cold Spray Additive Manufacturing: Investigation of Kinematic Spray Parameters on Deposition and Properties

Measurement and analysis of cold spray residual stress using arbitrary Lagrangian–Eulerian method

Numerical and Experimental Investigation Gas-Particle Two Phase Flow in Cold Spraying Nanostructured HA/Ti Composite Particle

The Analysis of Melting and Refining Process for In-Flight Particles in Supersonic Plasma Spraying

Simulation of Deposition Behavior of Bulk Amorphous Particles in Cold Spraying

Cold spray deposition: Significance of particle impact phenomena

Prediction of deformation characteristics and critical velocities during cold-spray: A new 3D model

SPH modeling and investigation of cold spray additive manufacturing with multi-layer multi-track powders

3D analysis of gas flow behavior and particle acceleration characteristics in cold spray additive manufacturing based on non-axisymmetric numerical models

Development of a material model for predicting extreme deformation and grain refinement during cold spraying