Abstract:Multi-stage microforming is increasingly used in manufacturing of the miniaturized parts with complex structures and geometries. Optimization design of this type of manufacturing process, however, is still challenging due to its unknown intrinsic nature of the process. In the multi-stage deformation and microforming, the size effect (SE), the strain path change (SPC), and the intragranularly misoriented grain boundary (IMGB) generated in previous forming stage, are the main factors governing the deformation behaviors of ultra-thin sheets. To gain thorough insights into their influences on deformation and elucidate the associated micro-scaled mechanisms, SS 316L ultra-thin sheets with the thickness of 0.1 mm and different mean grain sizes ( d ̄ ) were used for two-stage tensile tests under the conditions with distinct pre-strain εpre and intersection angle θSPC (the angle between the previous loading direction and subsequent one). Mechanical tests reveal that increasing εpre and θSPC reduces the yield stress and hardening rate in SPC tension, but this reduction gets smaller after increasing d ̄ . This is because more IMGBs with complex pattern are formed in relatively large grains, raising the permanent deformation resistance inside grains in subsequent tension. To model the IMGB-induced hardening, the SPC-induced softening, and the SE-induced concurrent facilitations to the hardening and softening, an enhanced crystal plasticity constitutive relation was established. The physical essence that IMGB obstructs dislocation movement, is used to model the IMGB-induced hardening based on the interactions between the main slip planes and IMGBs. The hardening facilitation caused by increasing grain size is implicitly incorporated in determining the saturated slip resistance. Modelling of the SPC-induced softening is based on the high Schmid factor grain fraction and its influences are governed by pre-strain and the defined SPC parameter. The softening facilitation caused by coarsening grains is modelled in establishing the initial slip resistance in SPC deformation. The proposed simulation procedure and constitutive relationship help with accurately predicting the mechanical response and microstructure evolution in micro-scaled SPC deformation, and also provide a basis for modelling and design of the multi-stage microforming of complex miniaturized parts.

Development of a material model for predicting extreme deformation and grain refinement during cold spraying

Achieving High Strength and High Ductility in Nanostructured Metals: Experiment and Modelling

Crystal Plasticity Modeling to Capture Microstructural Variations in Cold-Sprayed Materials

Prediction of deformation characteristics and critical velocities during cold-spray: A new 3D model

An experimentally validated dislocation density based computational framework for predicting microstructural evolution in cold spray process

Visualizing and Quantifying Deformation Microstructures in Cold Sprayed Materials

SPH modeling and investigation of cold spray additive manufacturing with multi-layer multi-track powders

A Residual Stress-Based Model for Viscoplastic Self-Consistent Simulation of Cold-Sprayed Al6061

Effect of particle oxidation, size and material on deformation, bonding and deposition during cold spray: a peridynamic investigation

Understanding Orientation-Dependent Plasticity in Laser Beam Powder Bed Fusion Stainless Steel Through Crystal Plasticity Modelling

A meshless computational framework for studying cold spray additive manufacturing including large numbers of powder particles with diverse characteristics

Experimental and Numerical Study of Al2219 Powders Deposition on Al2219-T6 Substrate by Cold Spray: Effects of Spray Angle, Traverse Speed, and Standoff Distance

Deformation Microstructures in Individual Cold Sprayed Al-Cu Alloy Particles Studied Via Precession Electron Diffraction and Transmission Kikuchi Diffraction

Nanocrystallization of interfacial microstructure of deformed particles in cold sprayed Ti6Al4V deposits

Crystal plasticity modelling of multi-stage deformation of ultra-thin sheets considering grain size effect and strain path change

Unraveling the Mesoscale Evolution of Microstructure during Supersonic Impact of Aluminum Powder Particles

Modeling of cryo-deformation based on grain size-dependent dislocation evolution

Effect of molten pool flow and recoil pressure on grain growth structures during laser powder bed fusion by an integrated model

Transition of Working Hardening Behaviors of Severe Plastic Deformation Processed Metals

Grain refinement in laser powder bed fusion: The influence of dynamic recrystallization and recovery

Research Progress on Numerical Simulation of the Deposition and Deformation Behavior of Cold Spray Particles