Abstract:Selective Laser Melting (SLM) has significant advantages in manufacturing complex structural components and refining the alloy microstructure; however, spatter, as a phenomenon that accompanies the entire SLM forming process, is prone to problems such as inclusions, porosity, and low powder recovery quality. In this paper, a Computational Fluid Dynamics–Discrete Particle Method (CFD–DPM) simulation flow for predicting the SLM spatter behavior is established based on the open-source code OpenFOAM. Among them, the single-phase flow Navier–Stokes equation is used in the Eulerian framework to equivalently describe the effect of metal vapor and protective gas on the flow field of the forming cavity, and the DPM method is used in the Lagrangian framework to describe the metal particle motion, and the factors affecting the particle motion include particle–particle collision, particle–wall collision, fluid drag force, gravity, buoyancy force, and additional mass force. In addition, the equivalent volume force and fluid drag force are used to characterize the fluid–particle coupling interaction. For the spatter behavior and powder bed denudation phenomenon, the calculation results show that the spatter height and the drop location show a clear correlation, and the powder bed denudation phenomenon is caused by the high-speed gas flow, causing the surrounding gas to gather in the forming area, which in turn drives the motion of the powder bed particles. For the effect of powder layer thickness on spatter and powder bed denudation, the calculation results show that the effect of powder layer thickness on the number of spatters is large (when the thickness was increased from 50 μm to 100 μm, the number of spatters increased by 157%), but the effect on spatter height and drop location distribution is small. When the powder layer thickness is small, the width of the denudation zone is significantly larger, but when the powder layer reaches a certain thickness, the width of the denudation zone does not show significant changes. It should be noted that the presented model has not been directly validated by experiments so far due to the difficulty of tracking the large-scale motion of SLM spatter in real time by current experimental means.

SPH modeling and investigation of cold spray additive manufacturing with multi-layer multi-track powders

A meshless computational framework for studying cold spray additive manufacturing including large numbers of powder particles with diverse characteristics

Numerical Study on Particle Behavior and Deposition Accuracy in Cold Spray Additive Manufacturing

Dynamic Modeling of Micro- and Nano-Sized Particles Impinging on the Substrate During Suspension Plasma Spraying

Modeling of Micro- and Nanoparticle Characteristics in DC Suspension Plasma Spray

Investigation of Dynamic Contact Between Cold Spray Particles and Substrate Based on 2D SPH Method

Development of a material model for predicting extreme deformation and grain refinement during cold spraying

Integral Numerical Modeling of the Deposition Profile of a Cold Spraying Process As an Additive Manufacturing Technology

Experimental and Numerical Study of Al2219 Powders Deposition on Al2219-T6 Substrate by Cold Spray: Effects of Spray Angle, Traverse Speed, and Standoff Distance

3D analysis of gas flow behavior and particle acceleration characteristics in cold spray additive manufacturing based on non-axisymmetric numerical models

Research Progress on Numerical Simulation of the Deposition and Deformation Behavior of Cold Spray Particles

Powder-scale Multi-Physics Modeling of Multi-Layer Multi-Track Selective Laser Melting with Sharp Interface Capturing Method

Capturing cold-spray bonding features of pure Cu from in situ deformation behavior using a high-accuracy material model

Crystal Plasticity Modeling to Capture Microstructural Variations in Cold-Sprayed Materials

New Process Implementation to Enhance Cold Spray-Based Additive Manufacturing

CFD–DPM Simulation Study of the Effect of Powder Layer Thickness on the SLM Spatter Behavior

An experimentally validated dislocation density based computational framework for predicting microstructural evolution in cold spray process

Simulation of the Cold Spray Particle Deposition Process

Modelling of Impact Behaviour of Cold Spray Particles: Review

Numerical Simulation of Selective Laser Melting Based on SPH Method

Simulation of Spatters Sticking Phenomenon in Laser Powder Bed Fusion Process Using the Smoothed Particle Hydrodynamics Method