Abstract:Multi-stage microforming is increasingly used in manufacturing of the miniaturized parts with complex structures and geometries. Optimization design of this type of manufacturing process, however, is still challenging due to its unknown intrinsic nature of the process. In the multi-stage deformation and microforming, the size effect (SE), the strain path change (SPC), and the intragranularly misoriented grain boundary (IMGB) generated in previous forming stage, are the main factors governing the deformation behaviors of ultra-thin sheets. To gain thorough insights into their influences on deformation and elucidate the associated micro-scaled mechanisms, SS 316L ultra-thin sheets with the thickness of 0.1 mm and different mean grain sizes ( d ̄ ) were used for two-stage tensile tests under the conditions with distinct pre-strain εpre and intersection angle θSPC (the angle between the previous loading direction and subsequent one). Mechanical tests reveal that increasing εpre and θSPC reduces the yield stress and hardening rate in SPC tension, but this reduction gets smaller after increasing d ̄ . This is because more IMGBs with complex pattern are formed in relatively large grains, raising the permanent deformation resistance inside grains in subsequent tension. To model the IMGB-induced hardening, the SPC-induced softening, and the SE-induced concurrent facilitations to the hardening and softening, an enhanced crystal plasticity constitutive relation was established. The physical essence that IMGB obstructs dislocation movement, is used to model the IMGB-induced hardening based on the interactions between the main slip planes and IMGBs. The hardening facilitation caused by increasing grain size is implicitly incorporated in determining the saturated slip resistance. Modelling of the SPC-induced softening is based on the high Schmid factor grain fraction and its influences are governed by pre-strain and the defined SPC parameter. The softening facilitation caused by coarsening grains is modelled in establishing the initial slip resistance in SPC deformation. The proposed simulation procedure and constitutive relationship help with accurately predicting the mechanical response and microstructure evolution in micro-scaled SPC deformation, and also provide a basis for modelling and design of the multi-stage microforming of complex miniaturized parts.

Modeling of cryo-deformation based on grain size-dependent dislocation evolution

Dislocation Density-Based Model for Flow Behavior of a Near-α Titanium Alloy Considering Effects of Initial Lamellar Thickness

Grain size and orientation affected deformation inhomogeneity and local damage of hot-deformed Al-Zn-Mg alloy

Crystal plasticity modelling of multi-stage deformation of ultra-thin sheets considering grain size effect and strain path change

Investigation of size effect on flow stress of Cu-3wt.%Ag-0.5 wt%Zr thin sheets at room and cryogenic temperature based on geometrically necessary dislocation evolution behavior

Modeling of material deformation behavior in micro-forming under consideration of individual grain heterogeneity

Temperature effect on tensile behavior of an interstitial high entropy alloy: Crystal plasticity modeling

Microstructure evolution, constitutive modeling and forming simulation of AA6063 aluminum alloy in hot deformation

Constitutive Modeling of Annealed OFHC with Wide Strain-Rate and Temperature Effects: Incorporating Dislocation Dynamics and Normalized Microstructural Size Evolution

Tensile properties and a modified s-Johnson-Cook model for constitutive relationship of AA7075 sheets at cryogenic temperatures

Electrical-thermal-mechanical coupled modeling and simulation on deformation behaviors of Ti6554 alloy in electrically-assisted micro-tension

Constitutive modeling and microstructure characterization of 2196 Al-Li alloy in various hot deformation conditions

Microstructure evolution mechanisms and a physically-based constitutive model for an Al–Zn–Mg–Cu–Zr aluminum alloy during hot deformation

Investigation of Grain Boundary and Orientation Effects in Polycrystalline Metals by a Dislocation-Based Crystal Plasticity Model

Crystal plasticity modeling of deformation behavior of Al–Al2Cu eutectics based on high-fidelity representative microstructures

Subgrain Size Modeling and Substructure Evolution in an AA1050 Aluminum Alloy during High-Temperature Compression

Cryogenic deformation tailors the dislocation accumulation mode to modify grain boundary character distribution of Incoloy 925

Dislocation mechanism based size-dependent crystal plasticity modeling and simulation of gradient nano-grained copper

Constitutive modeling for nanocrystalline metals based on cooperative grain boundary mechanisms

Unraveling size-affected plastic heterogeneity and asymmetry during micro-scaled deformation of CP-Ti by non-local crystal plasticity modeling

Enhanced deep drawing formability and deformation mechanism of aluminum alloy at cryogenic temperature