Abstract:This paper investigates the behavior of transverse defects under significant total strain in conditions of complex vortex metal flow implemented through the radial shear rolling (RSR) method. The aim of this study is to assess the applicability of RSR processing for the in-depth transformation of small ingots of special steel into bars, particularly for the manufacturing of structural elements in specialized construction projects such as nuclear power plants. Although a substantial total strain is anticipated to enhance the steel structure and contribute to defect closure, the question of the development or closure of potential casting defects remains unclear. To address this issue, model tests were conducted to simulate the implementation of RSR processing. Defect behavior data under very complex vortex metal flow and high strain conditions were obtained for the first time and have scientific merit. A small steel ingot with a 32 mm diameter, containing a simulated artificial defect in the form of a transverse through-hole with a 5 mm diameter, was employed. During rolling, the workpiece diameter was progressively reduced by 2 mm with each subsequent pass, reaching a final diameter of 20 mm. Additionally, to provide a more detailed visualization of the defect evolution process, the same defect was modeled in an aluminum bar over six passes, and changes in defect volume and shape were analyzed after each pass. A highly detailed 3D visualization of the actual defect evolution was achieved based on cross-sections from experimental workpieces. These data corresponded to the total strain levels obtained by finite element method (FEM) simulation. Notably, a consistent similarity was observed between the test results for both metals, revealing a reduction in defect volume of up to 67.7%. The deformational welding of defects in the outer sections, encompassing one-third of the rod’s radius, occurred in the initial passes. However, defects in the axial zone of the rods remained unclosed, lengthening and gradually decreasing proportionally to the elongation of the rod, akin to conventional rolling. Consequently, the radial shear rolling (RSR) method is unsuitable for ingots with substantial discontinuities in the axial zone post-casting. Nevertheless, the method ensures the total welding of defects located in the outer zones of the ingots, even with minor applied deformations and a slight decrease in the diameter of the deformed ingot. Such data were obtained for the first time and should contribute to future investigations in this field.

IDENTIFICATION OF INTERNAL DEFECTS IN THE FORGING OF THE ROTARY SHAFT MADE OF STEEL GRADE 35CRNI1MO

Microstructure Refinement and Crack Initiation in the Forging Process

Prevention of forging cracks in heavy hydro-generator shafts

Formation criterion of fissure defects in the inner wall of the radial forged steel tube

Investigation of crack-like defect in 15CDV6 (ESR) steel forging for aerospace applications

Analysis of Internal Crack in a Six-Ton P91 Ingot

Forming of Inner Faults Originating from Inclusions in the Heavy Forgings and the Process of Forging Control

Mechanism for Development of Faults Originating from Compound Inclusions in the Forging Process of 30cr2ni4mov Heavy Ingots

Analysis of Microstructure Evolution of Co-Cr-Mo Alloy during Isothermal Forging

Internal Shrinkage Crack in a 10 T Water-Cooled Steel Ingot with a Large Height-to-diameter Ratio

Modeling the Evolution of Casting Defect Closure in Ingots through Radial Shear Rolling Processing

Numerical Simulation of Central Shrinkage Crack Formation in a 234-T Steel Ingot

Inner crack with inclusion and forging process control of heavy forgings

Research on Casting Defects of 30Cr2Ni4MoV Heavy Steel Ingot

Processing and microstructure analysis on the precision rotary swaging of inner-stepped aero-engine shaft

The Mechanism of Faults Originating from Inclusions in the Plastic Deformation Processes of Heavy Forging

Metallographic Evaluation of Increased Susceptibility to Intermediate Embrittlement of Engine Valve Forgings Made of NCF 3015 High Nickel and Chromium Steel

Resarch on Microstructure and Property of Zirconium alloy in the Rotary forging process by GNN-FEM

Structural Features of Fatigue Crack Propagation of a Forging Die Made of Chromium-Molybdenum-Vanadium Tool Steel on Its Durability

Analysis of Internal Cracks in High Carbon Casting Bloom Induced by Soft Reduction Process and Its Improvement Using Numerical Simulations and Industrial Experiments

Possibilities of Measuring and Detecting Defects of Forged Parts in Die Hot-Forging Processes