Abstract:Abstract This paper presents an overview of a systems approach to the design and troubleshooting of IRCVs (Injection Rate Control Valves) used in deepwater chemical injection systems. The inherent problems associated with these simple flow regulators stem largely from the failure of design engineers to take a systems view in design. Along with the application of lessons learned from previous IRCV system failures, this systems approach provides a design method which will allow users to avoid many of the pitfalls inherent in design, installation, testing, commissioning and operation of IRCV systems. Introduction The conventional approach to injection of specialty/commodity chemicals is to use a separate chemical injection pump for each injection point. For topsides injection at low to moderate pressures, these pump systems are small and relatively inexpensive. In certain applications, such as in deepwater where injection pressures are high, these pump systems can be large, heavy and expensive. In deepwater and high pressure applications, a common alternative is to use distributed delivery systems featuring Injection Rate Control Valves (IRCVs). IRCVs are simple flow regulators which are designed to control flow to the individual users. It is easy to appreciate why these devices are being used with increasing frequency. Systems featuring them are cheaper, lighter, smaller and more flexible. However, many operators have little confidence in them. Many IRCV installations have failed and some have been made to work only after significant effort. While it can be difficult to definitively determine the particular reasons for their failure in many cases, it is not hard to picture why so many systems fail; there are multiple number of things that can go wrong with these systems. Failure to take a systems view explains many of the IRCV system failures. This paper presents a systems approach to the design and troubleshooting of IRCV systems. Our model of IRCV systems consists of two governing equations; 1) the injection system flow equation (pressure drop) and 2) the force balance across the IRCV piston. The force balance across the piston is important because the position of the piston determines the pressure drop and flowrate through the IRCV. Solving the system pressure drop equation simultaneously with the IRCV piston force balance is analogous to determining the operating point of a pump as the intersection of the pump curve and the system curve. Solving the system equations simultaneously is important because the design of the injection system impacts the operation of the IRCV. For example, system pressure drop impacts IRCV turndown and proportional offset. This paper includes:Descriptions of IRCVsDevelopment of the system modelA list of lessons learned, andA proposed design methodology.

METHODOLOGY FOR CALCULATING THE FLOW-RATE CHARACTERISTICS OF A CHEMICAL INJECTION METERING (THROTTLE) VALVE WITH A LAMINAR AND TURBULENT STAGE OF A SHUT-OFF AND CONTROL ELEMENT

New Method to Determine the Dynamic Fluid Flow Rate at the Gear Pump Outlet

Flow Rate Adjustable Ratio Analysis of a Novel Control Valve with Double Sleeve

Fluid Dynamics Analysis and Optimized Throttling Design of L-shaped Multi-Stage High Pressure Reducing Valve

Flow Rate Analysis of Compressible Superheated Steam Through Pressure Reducing Valves

Flow Analysis of a Needle Type Throttle Valves via Experimental and Numerical Methods

Parametric Analysis on Throttling Components of Multi-Stage High Pressure Reducing Valve

Numerical Analysis of Flow and Temperature Characteristics in a High Multi-Stage Pressure Reducing Valve for Hydrogen Refueling Station

Turbulent Compressible Flow Analysis on Multi-Stage High Pressure Reducing Valve

Modeling and Dynamic Characteristics Analysis on a Three-Stage Fast-Response and Large-Flow Directional Valve

The analysis of the main directions for reducing the intensity of mass flows of the working fluid through leaks in the working chamber of a piston long-stroke low-speed compressor stage

Flow-injection calibration procedures with the use of fully rotary valve

Research on A Novel Flow Rate Inferential Measurement Method and Its Application in Hydraulic Elevators

Research on the Effect of the Outlet Throttle Diameter Deviation on the Pressure Relief Rate of the Injector Control Valve

Comparative Evaluation of Methods for Calculating the Dynamics of Self-Acting Valves in Reciprocating Compressor Units

Numerical simulation of air injection in part load operating point

Successful Application of Chemical Injection Rate Control Valves

Numerical Modeling of High-Enthalpy Two-Phase Flow in a Channel with Transverse Injection of a Reactive Liquid

Technique for calculating technological parameters of non-Newtonian liquids injection into oil well during workover

Experimental Investigation of the Steady-State Flow Field with Particle Image Velocimetry on a Nozzle Check Valve and Its Dynamic Behaviour on the Pipeline System

HYDRAULIC CHARACTERISTICS OF TAP VALVE WITH A FLAT CLOSURE MEMBER