Abstract:Introduction. Failure of equipment, specifically pipes in the oilfield complex, due to the development of corrosion processes leads to numerous losses, destruction of expensive components, disruption of technological processes and, as a result, environmental damage. The use of anticorrosive coatings as an internal protection of oilfield pipes offers many advantages and can significantly reduce the rate of corrosion, but does not provide a complete solution to this problem. Destruction of internal anticorrosive polymer coatings (IACPC) occurs for numerous reasons. The causes and mechanisms of destruction are insufficiently investigated. Therefore, the aim of this work was to analyze the destruction of internal anticorrosive polymer coatings using practical examples, which made it possible to form and identify the main causes of damage and degradation of coatings during operation. Materials and Methods. A complex of laboratory studies was carried out to study the damage to internal polymer anticorrosive coatings during operation and to establish the main causes of destruction. The initial phase of the investigation involved a detailed examination of the materials related to the accident circumstances, including the operating conditions of the coated pipeline (composition of the operating medium, temperature, pressure, and presence of mechanical impurities), operation time, and type of polymeric material used. The second phase involved laboratory testing of the coating, which included the determination of layer thickness, dielectric continuity, adhesive strength (by the normal separation method), investigation of thermokinetic properties by means of differential scanning callometry (DSC), study of the coating structure using scanning electron microscopy. Results. Practical examples of the destruction of internal anticorrosive coatings of oilfield pipes were analyzed. For each case, characteristic signs of degradation of the anti-corrosive coating were identified. Changes in the microstructure of the coatings, as well as the formation of corrosion products, were observed depending on the type of destruction. The focus was on studying the degree of polymerization of the coating, both using the traditional method of determining the ΔTg parameter using DSC, and based on indirect signs detected during microscopic studies. Discussion and Conclusion. The practical cases of damage to the internal anticorrosion coating of pipes of the oil and gas complex considered in the article allowed us to divide the causes of destruction into three groups: operational, technological and defects during transportation, storage and construction and installation works. Based on these findings, we have formulated recommendations for manufacturers to ensure maximum performance from their coatings. It is noted that the compliance with the presented recommendations makes it possible to obtain internal anticorrosive polymer coatings with a minimum guaranteed lifespan of 15 years, as demonstrated by the successful operations of pipelines in Western Siberia, such as those operated by Surgutneftegaz PJSC and LUKOIL – Western Siberia LLC.

Causes of Damage to the Pressure Gauge Installed on the Process Pipeline

Experimental and Numerical Analysis of the Impact of Corrosion on Pipeline Failure Pressure

Analysis of Cracking of Pressure Gauge Spring Tube for Hydrogenation Plant

Review on Hydrogen-Induced Failure of Rubber O-Rings for High Pressure Hydrogen Storage Tanks

Determining the influence of an artificial defect on the mechanical properties of a flexible pipeline material during a rupture test

Crack Growth Analysis Of High-Pressure Equipment For Hydrogen Storage

Assessment of Operational Degradation of Pipeline Steels

Analysis of the causes of fracture of the main gas pipeline

Role of hydrogen in operational degradation of pipeline steel

Failure of a high-pressure flash gas pipeline from coal coke gasification to the cleaning section due to hydrogen-induced cracking

The Analysis of the Influence of Various Factors on the Development of Stress Corrosion Defects in the Main Gas Pipeline Walls in the Conditions of the European Part of the Russian Federation

Evaluation of Failure Pressure for Gas Pipelines with Combined Defects

Mechanical Properties of Gas Main Steels after Long-Term Operation and Peculiarities of Their Fracture Surface Morphology

Hydrogen related degradation in pipeline steel: A review

Wet H2S corrosion and degradation of pipeline in amine regeneration system

RESISTANCE OF FERRITE-PERLITE STEEL TUBING BRANCH PIPE METAL TO DESTRUCTION IN HYDROGEN SULFIDE MEDIUM

DEVELOPMENT OF LOADING MODELS AND ANALYSIS OF THE STRESS-STRAIN STATE OF THE MAIN GAS PIPELINE WITH COMPOSITE LININGS

Structural features of crack formation during corrosion cracking

The impact of residual technological stresses on the opening and stability of through cracks in pipeline elements

Embrittlement, degradation, and loss prevention of hydrogen pipelines

Destruction of Internal Anticorrosive Polymer Coatings of Oilfield Pipes during Operation