Abstract:This work improves the tribological behavior via innovative surface designs for slipper pairs in seawater axial piston pumps. 316L stainless steel and carbon fiber/polyether ether ketone (CF/PEEK) were selected as friction pair matching materials due to their good corrosion resistance, self-lubrication, and wear resistance. One type of smooth surface and five different types of pit nonsmooth surfaces were created on CF/PEEK specimens. Rotational sliding tests were performed on a friction and wear tester at a load of 200 N at five different sliding speeds (0.79, 1.18, 1.57, 1.96, and 2.36 m/s) under seawater lubrication. The experimental results indicate that the friction process of the smooth surface friction pair is mainly based on abrasive wear and adhesive wear. The friction coefficient range is 0.05–0.08, the specimen contact temperature is 38–75 °C, and the wear rates of 316L and CF/PEEK are 2.3 × 10−5 to 1.2 × 10−4 mm3/(MPa·m) and 5.6 × 10−4 to 7.6 × 10−3 mm3/(MPa·m), respectively. Pits on the specimen surface produce a hydrodynamic effect and store wear debris. The friction process of the nonsmooth surface friction pair is mainly controlled by a ploughing mechanism with only a slight amount of adhesive wear. The friction coefficient range is decreased to 0.03–0.07, the specimen contact temperature is decreased to 28–54 °C, and the wear rates of 316L and CF/PEEK are decreased to 1.2 × 10−5 to 9.1 × 10−5 mm3/(MPa·m) and 2.6 × 10−3 to 7.1 × 10−3 mm3/(MPa·m), respectively. The geometrical arrangement of the elliptical and tri-prism pits increases the convergence gap range and produces a higher bearing capacity. As the sliding speed increases, the friction coefficient first decreases and subsequently slightly increases, the specimen contact temperature increases, and the wear rate decreases.

Influence of Friction Properties Between Non‐Smooth Surface GFER and 316L Stainless Steel Under Seawater Lubrication and Simulation Research

Effect of Micro-Textured Surfaces and Sliding Speed on the Lubrication Mechanism and Friction-Wear Characteristics of CF/PEEK Rubbing against 316L Stainless Steel under Seawater Lubrication

Tribological Properties of Friction Pair between 316L Stainless Steel and CF/PEEK with Nonsmooth Surface under Seawater Lubrication

Influence of bionic non-smooth surface texture on tribological characteristics of carbon-fiber-reinforced polyetheretherketone under seawater lubrication

EFFECT OF MICRO-TEXTURES AND CrAlSiN COATINGS ON THE FRICTION AND WEAR PROPERTIES OF 316L STAINLESS STEELS IN SEAWATER

The Difference in Tribological Characteristics between CFRPEEK and Stainless Steel under Water Lubrication in Friction Testing Machine and Axial Piston Pump

On Frictional Performance of Sintering Materials Used by Mechanical Seals in Water

Friction and Wear Behavior Analysis of the Stainless Steel Surface Fabricated by Laser Texturing Underwater

Friction and Wear Behavior of Paired Pairs of Ceramics and Metal in High-Pressure Pump of Seawater Desalination

The Study of Micro-grating and Micro-square-column on Frictional Resistance Reduction of 316L Stainless Steel Surface

Study on the wear performance of 304 stainless steel aerospace joint bearings

Study on fretting friction properties based on GCr15 alloy and liquid epoxy resin protective coatings on GCr15 alloy

Tribological Behavior and Lubricating Mechanism of Si3N4 in Artificial Seawater

Influence of diamond-like carbon coatings and micro-texturing on friction and wear of seal interfaces: Experiment and simulation study

Effect of Lubricant Infiltration into the Groove-Like Surface Texture on the Friction Response of the Textured Stainless-Steel Contact Surface

Influence of Low Concentration Seawater on the Friction Corrosion Performance of Water–Glycol Fire-Resistant Hydraulic Fluid

Enhancement of the Water-Lubricated Tribological Properties of Hybrid PTFE/Nomex Fabric Laminate Composite via Epoxy Resin and Graphite Filler

Tribocorrosion Behavior of GCr15 Steel in Water–glycol Fire-Resistant Hydraulic Fluids (HFC) Containing Seawater

Simulation Study on Bearing Lubrication Mechanism and Friction Characteristics of the Biomimetic Non-Smooth Surface of a Cross-Scale, Second-Order Compound Microstructure

Effects of Surface Texturing and Laminar Plasma Jet Surface Hardening on the Tribological Behaviors of GCr15 Bearing Steel

Influence of Variable-Depth Groove Texture on the Friction and Wear Performance of GCr15–SiC Friction Pairs Under Water Lubrication