Abstract:In previously reported low-fluorine MOD-YBCO studies, the lowest F/Ba mole ratio of the precursor solution was 4.5. Further lowering the F/Ba ratio would bring benefits for the environment, thick film deposition, and an understanding of the heat treatment process. On the other hand, the F/Ba ratio must be at least 2 for full conversion of the Ba-precursor to BaF2 to avoid the formation of BaCO3, which is detrimental to the superconducting performance of YBCO films. In this study, a solution with a 2:1 F/Ba mole ratio was developed, and the fluorine content of this solution was approximately only 10.3% of that used in the conventional TFA-MOD method. Attenuated total reflectance-Fourier transform-infrared spectra (ATR-FT-IR) revealed that BaCO3 was remarkably suppressed in the as-pyrolyzed film-and eliminated at 700 degrees C. Thus, YBCO films with a critical current density (J(c)) of over 5 MA cm(-2) (77 K, 0 T, 200 nm thickness) could be obtained on lanthanum aluminate single-crystal substrates. In situ FT-IR spectra showed that no obvious fluorinated gaseous by-products were detected in the pyrolysis step, which indicated that all F atoms might remain in the film as fluorides. X-ray diffraction theta/2 theta scans showed the presence of BaF2-but not of YF3 or CuF2-in films quenched at 400-800 degrees C. The formation priority of BaF2 over YF3 and CuF2 was interpreted by examining the chemical equilibrium of the potential reactions. Our study could enlarge the synthesis window of precursor solutions for MOD-YBCO fabrication, and serve as a foundation for continuously and systematically studying the influence of fluorine content in the precursor solutions.

On the thermodynamics of Barium Oxyfluoride precursor in YBCO growth via MOD process

Effects of BaCO3 in transient liquid-assisted fluorine-free metal organic deposition on the growth process of YBCO

A Low-Fluorine Solution with the F/Ba Mole Ratio of 2 for the Fabrication of YBCO Films

A Low-Fluorine Solution With A 2:1 F/Ba Mole Ratio For The Fabrication Of Ybco Films

Artificial Control for Nucleation and Growth Rate of YBa2Cu3O7-δ Coated Conductors Prepared by Low Fluorine Chemical Solution Deposition

In situ high temperature optical microscopy study of phase evolution in YBa 2 Cu 3 O 7 d films prepared by a fluorine-free sol – gel route

Preparation of YBa2Cu3O7−δ Films by MOD Method Using Trifluoroacetate As Precursor

Thermodynamics and Kinetics Analysis of Mod-Ybco Heat Treatment Process Using in Situ Resistance Measurement Method

Precursor evolution and growth mechanism of BTO/YBCO films by TFA—MOD process

Surface Morphology and Profile Analysis for Five-Layer YBa 2 Cu 3 O 7− Δ Thick Films Prepared by Low-Fluorine Metallorganic Deposition

Application of thermal analysis and kinetic predictions to YBCO films prepared by chemical solution deposition methods

Transient Liquid Assisted Nucleation Mechanism of YBa 2 Cu 3 O 7− Δ in Coated Conductor Films Derived by BaF 2 Process

Mass Transport Of Beta-Diketonate Precursors For Mocvd Of Yba2cu3o7-Delta High T-C Superconducting Thin Films

Effect of precursor stoichiometry on the superconducting properties of fluorine-free sol–gel YBCO thin films

Formation and Characterization of YBa2Cu3O7−δ High-Tc Thin Films by MOCVD with Single Mixed Precursor

Influence of Partial Melting Temperature on Structure and Superconducting Properties of YBCO Film by Non-fluorine MOD

Low-Vacuum Pyrolysis of YBCO Films by Using Fluorine-Free Metal Organic Chemical Deposition

A Water-Free Metal Organic Deposition Method For Yba2cu3o7-Delta Thin Film Fabrication

Carbon Dioxide Controlled Thermal-Decomposition Reactions for Preparation of High Quality YBCO Films Derived from Fluorine-Free Solution

In-Plane and Out-of-Plane Anisotropy in the Optical and Dielectric Properties of Yba2cu3o7-X Superconducting Film

Controlled-Growth of $\hbox{YBa}_{2}\hbox{Cu}_{3}\hbox{O}_{7-\delta} $ Film Using Modified Low-Fluorine Chemical Solution Deposition