Abstract:In this work, a numerical study is conducted to investigate the improvement of in-plane behavior of weak brick masonry walls through assimilation of partially confining horizontal and vertical reinforced concrete (RC) bands. The bands are considered to be assimilated with the existing walls by cutting grooves over the partial thickness of the wall in a easy-to-construct manner. For numerical modeling of the wall width and without partially confining elements, a three-dimensional (3D) macro-modeling approach is utilized as it is computationally efficient compared to other modeling approaches while representing the global behavior reasonably well. The components of macro-models are discretely modeled. The concrete damage plasticity (CDP) model is considered to describe the non-linear behavior of the concrete and masonry for crushing and cracking failures. Steel reinforcements are considered as bilinear with hardening and modeled with perfect adhesion with the surrounding concrete using embedded constraints. Experimental results obtained from the full-scale tests at the Structural Engineering laboratory of IIT Kanpur have been utilized to validate the numerical model. The responses obtained from the numerical model of both with and without RC bands demonstrate that the models reasonably capture the experimental behavior such as initial stiffness, peak loads and post-peak behavior. The initial peak load from the numerical model of without and with RC bands was found to be 3.2% and 6.9% lower than the experimental value, respectively. Although post-yield trends of numerical and experimental results show similar behavior for walls without and with RC bands, the numerical model underestimates the post-yield strength for the wall without RC bands. This deviation can be attributed to the masonry dominated post-peak behavior coupled with modeling assumptions and values of model parameters used for the numerical analysis. Finally, to understand the influence of various parameters on lateral strength, a parametric study has been conducted. From the parametric study, it has been found that the compressive strength of masonry and band aspect ratio are the two most important parameters governing the strength of the wall. Finally, it is noted that a wall with band aspect ratio close to unity provides superior ductile behavior.

Mitigating damages to infill walls under combined in-plane and out-of-plane loadings using a spider web-inspired strengthening strategy: Numerical analyses

Dynamic Progressive Collapse Response of Multi-Storey Frame Structures with Masonry Infills

Study on the RC Frame with the Partial Infill Wall in Pushover Analysis

Out-of-plane strengthening of URM walls using different fiber-reinforced materials

Experimental Analysis of Out-of-plane Behavior of Masonry Infill Walls Strengthened with Textile Reinforced Mortar and Wall Post in Autoclaved Aerated Concrete Frames

Investigation on the influence of previous in-plane loading on the out-of-plane behavior of the innovative damped masonry infill wall

Analytical formulation describing the behaviour of URM walls seismically strengthened using timber strong-backs

Enhancing the In-Plane Behavior of a Hybrid Timber Frame-Mud and Stone Infill Wall Using PP Band Mesh on One Side

Effect of in-plane damage on the out-of-plane mechanical performance of infill walls with recycled concrete blocks

Combined Strengthening Techniques to Improve the Out-of-Plane Performance of Masonry Walls

In-Plane Shear Behavior of Unreinforced Masonry Wall Strengthened with Bamboo Fiber Textile-Reinforced Geopolymer Mortar

Quasi-static, Cyclic Loading Tests of RAC Brick Masonry Walls Strengthened by Basalt Textile Reinforced Concrete

A block-based numerical strategy for modeling the dynamic out-of-plane behavior of unreinforced brick masonry walls

Numerical investigation on the effect of infill masonry on lateral behaviour of surrounding RC frame

Numerical and Experimental Investigation on Cyclic Behavior of Masonry Infill Walls Retrofitted with CFRP

Improving In-Plane Behavior of Weak Brick Masonry Walls Through Assimilation of Partially Confining RC Bands

Tie system to upgrade out‐of‐plane performance of infill masonry walls

In-Plane Lateral Response of a Full-Scale Masonry Subassemblage with and without an Inorganic Matrix-Grid Strengthening System

Nonlinear Behavior of a Masonry Subassemblage Before and After Strengthening with Inorganic Matrix-Grid Composites

Anti-collapse mechanism and reinforcement methods of composite frame with CFST columns and infill walls

Discrete macro - models of nonlinear interlocking mechanisms in the out-of-plane failure of masonry walls