Abstract:In this work, a numerical study is conducted to investigate the improvement of in-plane behavior of weak brick masonry walls through assimilation of partially confining horizontal and vertical reinforced concrete (RC) bands. The bands are considered to be assimilated with the existing walls by cutting grooves over the partial thickness of the wall in a easy-to-construct manner. For numerical modeling of the wall width and without partially confining elements, a three-dimensional (3D) macro-modeling approach is utilized as it is computationally efficient compared to other modeling approaches while representing the global behavior reasonably well. The components of macro-models are discretely modeled. The concrete damage plasticity (CDP) model is considered to describe the non-linear behavior of the concrete and masonry for crushing and cracking failures. Steel reinforcements are considered as bilinear with hardening and modeled with perfect adhesion with the surrounding concrete using embedded constraints. Experimental results obtained from the full-scale tests at the Structural Engineering laboratory of IIT Kanpur have been utilized to validate the numerical model. The responses obtained from the numerical model of both with and without RC bands demonstrate that the models reasonably capture the experimental behavior such as initial stiffness, peak loads and post-peak behavior. The initial peak load from the numerical model of without and with RC bands was found to be 3.2% and 6.9% lower than the experimental value, respectively. Although post-yield trends of numerical and experimental results show similar behavior for walls without and with RC bands, the numerical model underestimates the post-yield strength for the wall without RC bands. This deviation can be attributed to the masonry dominated post-peak behavior coupled with modeling assumptions and values of model parameters used for the numerical analysis. Finally, to understand the influence of various parameters on lateral strength, a parametric study has been conducted. From the parametric study, it has been found that the compressive strength of masonry and band aspect ratio are the two most important parameters governing the strength of the wall. Finally, it is noted that a wall with band aspect ratio close to unity provides superior ductile behavior.

Numerical investigation on the effect of infill masonry on lateral behaviour of surrounding RC frame

Cyclic Response of Infilled RC Frames with Window and Door Openings: Experimental Results and Damage Interpretation

Dynamic Progressive Collapse Response of Multi-Storey Frame Structures with Masonry Infills

Experimental Study of RC Frames with Window and Door Openings Under Cyclic Loading

Study on the RC Frame with the Partial Infill Wall in Pushover Analysis

Influence of Masonry Infill Walls on the Seismic Assessment of Non-Seismically Designed RC Framed Structures

Influence of masonry infills on seismic performance of BRB‐retrofitted low‐ductile RC frames

Numerical and Experimental Investigation on Cyclic Behavior of Masonry Infill Walls Retrofitted with CFRP

Analysis of RC Building Frame with and Without Masonry Infill Walls

Experimental and numerical investigation of hysteretic earthquake behavior of masonry infilled RC frames with opening strengthened by adding rebar-reinforced stucco

Seismic Performance Assessment of Masonary Infilled RC Frames by Using Staad PRO

Study on in-plane/out-of-plane seismic performance of masonry-infilled RC frame with openings and a new type of flexible connection

Numerical Simulation Study of Progressive Collapse of Reinforced Concrete Frames with Masonry Infill Walls under Blast Loading

Seismic design of RC moment-resisting frames with concrete block infill walls considering local infill-frame interactions

Improving In-Plane Behavior of Weak Brick Masonry Walls Through Assimilation of Partially Confining RC Bands

A double-strut macro-modelling approach for the in-plane analysis of masonry infilled RC frames with openings

Effect of Infilled Frames on Reduction Factor (R) for RC Irregular Structure

Field measurements for calibration of simplified models of the stiffening effect of infill masonry walls in high-rise RC framed and shear-wall buildings

Numerical Modeling of Masonry Infilled Reinforced Concrete Building during Construction Stages Using ABAQUS Software

Dynamic Tests of a Large-Scale Three-Story RC Structure with Masonry Infill Walls

Numerically based proposals for the stiffness and strength of masonry infills with openings in reinforced concrete frames