Abstract:Masonry structures often exhibit poor seismic performance during earthquakes owing to their low material strength, structural integrity, and ductility. To address the mechanism of in-plane damage and collapse of masonry walls subjected to earthquake ground motion, three full-size brick walls, one with structural columns and two without structural columns, were designed and constructed in this experimental study to quantitatively investigate the effect of structural columns on the seismic performance of masonry walls. Quasi-static tests of masonry walls subjected to cyclic lateral loading were conducted using electrohydraulic servo actuators. The in-plane damage evolution and failure mode of the masonry walls under lateral loading were investigated. A numerical model with a novel plastic damage constitutive model of masonry was established. The accuracy of this model and the calculation results were verified by comparing them with the crack development and mechanical property curves obtained from the experiments. Based on the numerical model, a parametric analysis was conducted to investigate the influence of critical factors, such as mortar strength, vertical load, and height-to-width ratio, on the seismic performance of masonry structures. The test results showed that structural columns can effectively improve the performance of masonry structures. Properly installed structural columns can improve the peak load-bearing capacity, ductility, and energy dissipation of masonry structures. The masonry damage constitutive model used in this study could simulate the damage to masonry wall specimens well and reflect the hysteretic curves of the specimens within an acceptable range of accuracy. Thus, it provides a valuable reference for physical experiments. An appropriate mortar strength and vertical compressive stress can effectively enhance the load-bearing capacity of masonry structures within a certain range. For structural column walls. Walls with mortar strengths (average compressive strength) of 12.5 MPa, 10 MPa, 7.5 MPa, and 5 MPa showed an increase in peak bearing capacity of 26.2 %, 23.9 %, 18.5 %, and 9.4 %, respectively, compared to walls with mortar strengths (average compressive strength) of 2.5 Mpa. The aspect ratio had a significant impact on the shear load-bearing capacity of the masonry walls. An increase in the aspect ratio led to a transition from shear failure to flexural failure and a subsequent decrease in shear load-bearing capacity. For masonry walls with structural columns, increasing the diameter of the longitudinal steel in the structural columns can enhance the load-bearing capacity of the masonry wall, resulting in a significant improvement in its overall performance.

Investigation on the influence of previous in-plane loading on the out-of-plane behavior of the innovative damped masonry infill wall

Cyclic Response of Infilled RC Frames with Window and Door Openings: Experimental Results and Damage Interpretation

Experimental Investigation of Effect of Section Configuration on Seismic Performance of an Innovative Integrated Concrete Masonry Wall System

Experimental Study of RC Frames with Window and Door Openings Under Cyclic Loading

Simulation Of Collapse Process Of Masonry Walls Based On Expanded Discrete Element Method

Mitigating damages to infill walls under combined in-plane and out-of-plane loadings using a spider web-inspired strengthening strategy: Numerical analyses

Experimental Analysis of Out-of-plane Behavior of Masonry Infill Walls Strengthened with Textile Reinforced Mortar and Wall Post in Autoclaved Aerated Concrete Frames

Effect of in-plane damage on the out-of-plane mechanical performance of infill walls with recycled concrete blocks

Damage evolution and failure mechanism of masonry walls under in-plane cyclic loading

In-plane Behavior of Chuan-Dou Style Wooden Frames with Infill under Cyclic Loading

Explicit Approach for the In-Plane Cyclic Behaviors of Unreinforced Masonry Structures Using Finite Particle Method

Determining Experimental Ductile Behavior of Composite Walls Considering Second-Order Effects: A Case Study for Multi-Celled CFST Walls

Enhancing the In-Plane Behavior of a Hybrid Timber Frame-Mud and Stone Infill Wall Using PP Band Mesh on One Side

In-Plane Lateral Response of a Full-Scale Masonry Subassemblage with and without an Inorganic Matrix-Grid Strengthening System

An Investigative Study for the Seismic Performance of Composite-Reinforced Masonry Wall with Prestressing Technology

Experimental Investigation on the In-Plane and Out-of-plane Interaction of Isolated Infills in RC Frames

In-Plane Cyclic Response of Reinforced Concrete Masonry Shear Wall with Large Cross-Section Core Columns

OUT-OF-PLANE BEHAVIOUR OF UNREINFORCED MASONRY WALLS WITH TOPOLOGICAL INTERLOCKING BRICK

In-Plane Cyclic Behaviour Comparison of Adobe Wall Retrofitted by Mortar Enhanced by Physical and Chemical Methods

Out-of-plane strengthening of URM walls using different fiber-reinforced materials

Discrete macro - models of nonlinear interlocking mechanisms in the out-of-plane failure of masonry walls