Abstract:The High Luminosity Large Hadron Collider (HL-LHC [1]), an upgrade of the LHC, is set to become operational in 2029, aiming to achieve instantaneous luminosities 5–7.5 times larger than the nominal value of the LHC. However, unlocking the full physics potential at this much higher luminosity level necessitates a tenfold increase in the data bandwidth processed by ATLAS. This poses significant challenges to the design of the Trigger and Data Acquisition systems. To address these challenges, a baseline architecture has been chosen for the ATLAS Phase-II upgrade, relying on a single-level hardware trigger known as the Level-0 Trigger. This trigger has a maximum rate of 1 MHz and a latency of 10 μs. Central to this upgrade is the inclusion of a new subsystem — the Global Trigger [2]. This component performs complex algorithms, akin to those currently used in Phase-I high-level trigger software (such as Topoclustering), on full-granularity calorimeter data. The Global Trigger is divided into three sublayers: the Multiplexer Processor (MUX) layer, the Global Event Processor (GEP) layer, and the Global to Central Trigger Processor [3] interface (gCTPi). A full-function Global Common Module (GCM) hardware prototype has been designed to fulfill the requirements of all three sublayers of the Global Trigger, featuring different firmware loads. This GCM prototype, based on the ATCA [4] front board form factor, incorporates two of the latest AMD (Xilinx) Versal Premium devices VP1802 [5]. These devices boast double the density of the Virtex UltraScale+ FPGA VU13P used in the previous design [6] and include an integrated SoC with a completely new architecture. To handle high-speed I/Os, this GCM prototype employs twenty 12-channel 25.7 Gb/s FireFly [7] optical engines. The estimated maximum power consumption of this GCM prototype is 400 W, which falls within the cooling capabilities of the ATLAS ATCA shelf. To ensure power integrity, signal integrity, and thermal performance, extensive PCB simulations and thermal simulations have been done to guide the layout design of the GCM prototype. This paper provides an in-depth overview of the design process for this full-function GCM prototype hardware, with a particular focus on technology choices and simulation results.

An FPGA-based front-end module emulator for the High Granularity Timing Detector

The Development of the Global Feature Extractor for the LHC Run-3 Upgrade of the L1 Calorimeter Trigger System

Performance of a front-end prototype ASIC for the ATLAS High Granularity Timing Detector

Performance of a Front End prototype ASIC for picosecond precision time measurements with LGAD sensors

Gfex, the ATLAS Calorimeter Level-1 Real Time Processor

The Prototype Design of Gfex — a Component of the L1calo Trigger for the ATLAS Phase-I Upgrade

Design and Implementation of High-Precision Timing Module for NR Terminals Based on FPGA

The Amc13xg: A New Generation Clock/Timing/Daq Module for Cms Microtca

8-Channel 14-Bit 125mhz FADC Electronics with 1G Ethernet Readout Based on ZYNQ for HPGe Detector

Machine learning evaluation in the Global Event Processor FPGA for the ATLAS trigger upgrade

A full-function Global Common Module prototype for ATLAS Phase-II upgrade

FATALIC: A novel CMOS front-end readout ASIC for the ATLAS Tile Calorimeter

Development and data path integration test of the global Feature EXtractor for the ATLAS Level-1 calorimeter trigger system Phase-I upgrade

FELIX: the New Detector Interface for the ATLAS Experiment

Overview of the ATLAS High-Granularity Timing Detector: project status and results

Project and Implementation of a Quantum Logic Gate Emulator on FPGA Using a Model-Based Design Approach

Multi-Mode Debugging System for VLSI Designs Using Different Types of FPGAs

JTAG-based Remote Configuration of FPGAs over Optical Fibers

ETROC1: The First Full Chain Precision Timing Prototype ASIC for CMS MTD Endcap Timing Layer Upgrade

FADC electronics design for HPGe detector